Bosch A4VG A4VG 32 Series Скачать руководство пользователя | Manualshive

Страница: 64 / 68

background image

64/68 Troubleshooting

Bosch Rexroth AG

, A4VG Series 32, RE 92003-01-B/12.2015

Table 13: Axial piston unit malfunction table

Malfunction

Possible cause

Remedy

Pressure/flow fluctuations
or instabilities

Insufficient air bleeding of the hydraulic system

Fill axial piston unit, suction line for
the hydraulic pump and the reservoir
Completely air bleed axial piston unit
and hydraulic system
Check correct installation position

Insufficient suction conditions, e.g. insufficient
dimensioning of the suction line, viscosity of
the hydraulic fluid too high, suction height too
high, suction pressure too low, contaminants in
the suction line, suction filter too small, etc.

Machine/system manufacturer: check
the system, e.g. optimize inlet conditions,
use suitable hydraulic fluid
Fill the suction line with hydraulic fluid

Remove contaminants from the suction line

Check the filter system and change the
filter as necessary

Oscillate pressure limitation and pressure
control valves of the axial piston unit (boost
pressure-relief valve, high-pressure relief
valve,pressure cut-off)

Air bleed axial piston unit and hydraulic system

Contact Bosch Rexroth Service

Unstable control signal

Contact machine/system manufacturer or
Bosch Rexroth Service

Malfunction in the control devices or the
controller

Contact Bosch Rexroth Service

Excessive hydraulic fluid
temperature and housing
temperature

Excessive inlet temperature in the axial piston
unit

Machine/system manufacturer: inspect system,
e.g., malfunction in the cooler, insufficient
hydraulic fluid in the reservoir

Wrong setting or malfunction in the pressure
relief and pressure control valves (e.g., high-
pressure relief valve, pressure cut-off,
pressure controller)

Optimize the adjustment of the pressure
limitation and pressure control valves of the
axial piston unit and the pressure safeguarding
in the hydraulic system
Contact Bosch Rexroth Service

Contact machine/system manufacturer

Flushing flow of the flushing valve too low

Contact Bosch Rexroth Service

Axial piston unit worn

Replace axial piston unit, contact
Bosch Rexroth Service

«
...
62
63
64
65
66
...
»

Содержание A4VG A4VG 32 Series





































































Отзывы:

Нет отзывов

Похожие инструкции для A4VG A4VG 32 Series

Бренд: TDRFORCE Страницы: 12

Бренд: Dantherm Страницы: 12

Бренд: German pool Страницы: 11

Бренд: samhydraulik Страницы: 7

ACT Signature Series

Бренд: Aqua Comfort Страницы: 2

VED E 8 INT Series

Бренд: Vaillant Страницы: 236

Бренд: A.O. Smith Страницы: 16

TurboSilence InverX IXCR36

Бренд: Fairland Страницы: 117

Бренд: Pacific hydrostar Страницы: 33

Бренд: Quattroflow Страницы: 28

Бренд: Nakayama Страницы: 29

Бренд: Heat Controller Страницы: 15

Бренд: hajdu Страницы: 65

Бренд: Simer Страницы: 35

Бренд: Alemite Страницы: 16

Бренд: Homelite Страницы: 36

Бренд: red lion Страницы: 8

FlowSol B HE WMZ

Бренд: Resol Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды