manualshive.com logo in svg

Bosch A20V(L)O, Инструкция по эксплуатации

Поделиться
Скачать
Bosch A20V(L)O Скачать руководство пользователя страница 5

 

About this documentation 5/68

 

RE 93100-01-B/2019-09-10, A20V(L)O Series 1, 

Bosch Rexroth AG

1  About this documentation

1.1  Validity of the documentation

This documentation is valid for the following product:

 

• Axial piston variable double pump A20V(L)O (series 1)

The axial piston variable double pump consists of tried and tested components of 
the following variable pumps:

 

• Axial piston variable pump A10VO (series 52, size 60)

 

• Axial piston variable pump A11VO (series 10, size 95)

 

• Axial piston variable pump A11VLO (series 11, sizes 190 and 260)

 

• Axial piston variable pump A4VSO (series 30, size 520)

This documentation is intended for machine/system manufacturers, assemblers and 
service engineers.
This documentation contains important information on the safe and proper 
transport, installation, commissioning, operation, maintenance, removal and simple 
troubleshooting of the axial piston unit.

 

▶

Read this documentation completely, in particular chapter 2 "Safety instructions" 
on page 9 and chapter 3 "General instructions on property damage and 
product damage" on page 16 before you start work with the axial piston unit.

1.2  Required and supplementary documentation

 

▶

Only commission the axial piston unit if the documentation marked with the book 
symbol 

 is available to you and you have understood and observed it.

Table 1: Required and supplementary documentation

Title

Document number

Document type

Order confirmation

Contains the order-related technical data for your axial piston variable 
double pump A20V(L)O.

–

Order confirmation

Installation drawing

Contains the outer dimensions, all connections and the hydraulic circuit diagram 
for your A20V(L)O axial piston variable double pump.

Please request 
the installation 
drawing from 
your contact 
at Bosch Rexroth.

Installation drawing

Axial piston variable double pump A20VO

Contains the permissible technical data, ports, main dimensions and 
circuit diagrams.

93100

Axial Piston variable Pump A10VO

Contains additional technical data for size 60.

92703

Axial piston variable pump A11VO

Contains additional technical data for sizes 95 to 260.

92500

Axial piston variable pump A4VSO

Contains additional technical data for size 500 (size 520 not included in the 
standard program).

92050

Control systems HM, HS, HS5 and EO

Contains all control systems for size 520.

92076

Hydraulic fluids based on mineral oils and related hydrocarbons

Describes the requirements for hydraulic fluids on mineral oil basis and related 
hydrocarbons for operation with Rexroth hydraulic components, and provides 
support for selection of suitable hydraulic fluids for the hydraulic system.

90220

Содержание A20V(L)O





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды