Bosch A20V(L)O Скачать руководство пользователя

Страница: 23 / 68

Transport and storage 23/68

RE 93100-01-B/2019-09-10, A20V(L)O Series 1,

Bosch Rexroth AG

6 Transport and storage

▶

Always observe the necessary ambient conditions for transport and storage;
see chapter 6.2 "Storing the axial piston unit" on page 26.

Information on unpacking can be found in chapter 7.1 "Unpacking" on page 28.

6.1 Transporting the axial piston unit

The following transportation options are available depending on weight and duration
of transport:

• Transport by hand

• Transporting with a lifting device (eye bolt or lifting strap)

Table 6: Dimensions and weights

Size

190

260

520

Weight

107

213

275

640

Width

mm Dimensions vary by equipment. The values applicable for your axial piston

unit can be found in the installation drawing (request if necessary).

Height

Depth

Weight may vary by equipment.

6.1.1 Transport by hand

Up to a specific maximum weight, axial piston units can be transported by hand
for a short distance. Observe the national regulations in your country. To prevent
health damage, we recommend renouncing any transport by hand.

CAUTION!

Risk of injury due to heavy loads!

Health hazard from carrying axial piston units.

▶

Only manually transport the axial piston unit for a short period of time.
Observe the national regulations in your country for manual transport.

▶

Always use appropriate lifting, lowering and moving techniques.

▶

Use your personal protective equipment (e.g. safety goggles, safety gloves,
suitable working clothes, safety shoes).

▶

Do not transport the axial piston unit by sensitive assembled parts
(e.g. sensors or valves).

▶

Carefully place the axial piston unit on the seating to prevent it from being
damaged.

Dimensions and weights

Содержание A20V(L)O





































































Результаты поиска

Содержание A20V(L)O

Отзывы:

Похожие инструкции для A20V(L)O

Бренды по названию

Популярные бренды

Bosch A20V(L)O, Инструкция по эксплуатации

Результаты поиска

Содержание A20V(L)O

Отзывы:

Похожие инструкции для A20V(L)O

Бренды по названию

Популярные бренды