background image

Technical information and reports

47

Condens 7000 WP – 6721841195 (2022/01)

15.2

Technical Specifications

Condens 7000 WP GC7000WP

GC7000WP 50 GC7000WP 65 GC7000WP 85

GC7000WP 

100

General information

Unit

Rated heat output (50/30 °C) [P

n

 cond]

kW

14.3 – 49.9

14.3 – 69.5

20.8 – 84.5

20.8 – 99.5

Rated heat output (80/60 °C) [P

n

]

kW

13.0 – 46.5

13.0 – 62.6

18.9 – 80.0

19.0 – 94.5

Rated thermal load G20, G25, G25.3 (UW) [Q

n

 (Hi)]

kW

13.3 – 47.5

13.3 – 64.3

19.3 – 82.0

19.3 – 96.5

Rated thermal load G31 (UW) [Q

n

 (Hi)]

kW

13.3 – 47.5

13.3 – 64.3

19.3 – 82.0

19.3 – 96.5

Efficiency (37/30 °C) partial load 30% in accordance with EN 
15502

%

108.4

108.7

109.1

108.7

Efficiency (80/60 °C) full load

%

98.5

98.9

98.7

98.6

Standby loss in accordance with EN 15502.

%

0.24

0.18

0.14

0.12

Standard efficiency of heating curve (75/60 °C)

%

106.0

106.9

106.7

106.8

Standard efficiency of heating curve (40/30 °C)

%

109.7

110.4

110.2

110.3

Pump overrun

min

2

IP classification [IP rating]

IP X0D

Appliance class in accordance with EN 15502.

B

23(p)

, B

53(p)

, C

13(x)

, C

33(x)

, C

43(x)

, C

53(x)

, C

63(x)

, C

83(x)

, C

93(x)

Product ID no.

CE-0085DL0480

Temperature classification in accordance with EN 14471.

T120

Appliance fuse

230 V, 5AF

Mains voltage, frequency [U]

230 V, 50 Hz

Power input (without pump), 

standby / partial load / full load

W

2 / 8 / 31

2 / 8 / 65

2 / 10 / 88

2 / 10 / 133

Maximum possible installation altitude of boiler

m

1200

Permissible ambient temperature

°C

0 - 40

Maximum flow temperature [T

max

]

°C

85

Maximum permissible water pressure [PMS]

bar

6

Maximum condensate accumulation rate

l/h

6.0

7.6

9.3

11.0

Connections

Flue gas connection/concentric air supply

mm

110/160

Heating flow/return pipe (wall mounted gas condensing boiler)

inch

G1½

Gas connection (wall mounted gas condensing boiler)

inch

R1

Condensate drain (flexible drain hose)

mm

24

Emission values in accordance with EN 13384

CO

2

 content with natural gas G20, partial load/full load

%

8.4 / 9.3

8.4 / 9.3

8.2 / 9.1

8.1 / 9.1

CO

2

 content with natural gas G25, partial load/full load

%

8.3 / 9.1

8.4 / 9.1

8.2 / 9.1

8.1 / 9.1

CO

2

 content with natural gas G25.3, partial load/full load

%

8.4 / 9.1

8.4 / 9.1

8.2 / 9.1

8.1 / 9.1

CO

2

 content with propane G31, partial load/full load

%

9.5 / 10.0

9.5 / 10.0

9.1 / 10.0

9.0 / 10.0

O

2

 content with natural gas G25.3, partial load/full load

%

5.7 / 4.4

5.7 / 4.4

6.1 / 4.4

6.3 / 4.4

O

2

 content with propane G31, partial load/full load

%

6.5 / 5.7

6.5 / 5.7

7.1 / 5.7

7.3 / 5.7

CO output G20 at full load (n = 1)

ppm

31

63

70

81

Standard emission factor (EN15502) CO

mg/m

3

2.7

10.8

17.2

23.4

Standard emission factor (EN15502) NOx G20 (average)

mg/kWh

25

34

34

38

NO

x

 class

6

Flue gas mass flow rate at min./max. rated heat output

g/s

6.5/21.6

6.5/29.2

9.8/38.0

9.8/44.7

Flue gas temperature at 80/60 °C, partial load/full load

°C

56 / 59

56 / 61

56 / 66

56 / 73

Flue gas temperature at 50/30 °C, partial load/full load

°C

32 / 39

32 / 43

34 / 50

34 / 53

Differential pressure gas/air (with partial load)

Pa

-5

Flue gas class for LAS (Germany only)

G61

Fan discharge pressure

Residual head of fan (p

max

)

Pa

71

130

162

226

DN110/185, B

23p

, partial load/full load 

Pa

50 / 83

50 / 148

50 / 177

50 / 241

DN110/185, with overpressure flap, B

23p

, partial load/full load

Pa

41 / 41

50 / 100

50 / 108

50 / 148

DN110/160, C

x3x

, partial load/full load

Pa

50 / 71

50 / 130

50 / 162

50 / 226

DN110-110, C

x3x

, partial load/full load

Pa

50 / 71

50 / 130

50 / 162

50 / 226

Dimensions and weight

Содержание 7736 702 194





















































Отзывы: