background image

6 720 644 951 (2014/11)

330 PN

32 | LIFETIME LIMITED WARRANTY FOR BOSCH TANKLESS WATER HEATERS

10

LIFETIME LIMITED WARRANTY FOR BOSCH TANKLESS WATER HEATERS

MODELS COVERED

This limited warranty is provided by Bosch Thermotechnology 
Corp. (BTC) and covers models 330 PN (hereinafter referred 
to as "Water Heater"). This warranty is provided as long as the 
Water Heater remains in the possession of the original 
purchaser and installed at its original place of installation.

WARRANTY COVERAGE

HEAT EXCHANGER -Limited Warranty

BTC warrants that the heat exchanger will remain free of leaks 

for Fifteen (15) years from the date of original installation pro-

vided that the heat exchanger is properly maintained by a qual-

ified heating contractor and the other conditions of this 

warranty are met.  If during this time a leak occurs and BTC 

determines that this leak is the result of a defect in workman-

ship or materials, BTC, will replace the heat exchanger.  If the 

Water Heater is installed in other than a single family dwelling, 

the heat exchanger warranty is limited to two (2) years from 

date of original installation.

OTHER WATER HEATER PARTS

If any other part fails within two (2) years after original 
installation, BTC will furnish a replacement part fee of charge.
The Water Heater may be delivered with components not 
manufactured by BTC ("Other Components). Other 
Components are warranted by their manufacturer. BTC also 
will warrant the Other Components to be free from defects in 
workmanship and material for one year from the date of 
installation, provided they are installed and properly 
maintained by a qualified heating contractor and the other 
conditions of this warranty are met. If a defect exists in the 
Other Components, BTC will repair or replace them, if BTC 
determines that a defect in workmanship or materials exists.

SERVICE LABOR COSTS

This warranty provides labor costs, at BTC approved rates, for 
one (1) year from the date of original installation, provided it is 
installed and properly maintained by a qualified heating 
contractor and the other conditions of this warranty are met.

ITEMS NOT COVERED

This limited warranty does not cover the following 
circumstances:

1. Components or parts not provided by BTC.

2. Serviceable items and normal maintenance as required per 
the Installation Manual.

3. The workmanship of any installer. BTC disclaims and does 
not assume any liability of any nature for unsatisfactory 
performance caused by improper installation, repair or 
maintenance.

4. Any labor or material costs for removal, reinstallation, repair 
and replacement of the defective component or part unless 
otherwise provided above.

5. Transportation to BTC, if necessary.

6. Damage caused by operation of the Water Heater in a 
corrosive atmosphere, scale depots and/or highly mineralized 
or unsoftened water supply, electrical failures, flooding, or acts 
of God.

7. Any Water Heater that has a failure of malfunction resulting 
from operation with either the flame sensor rod or overheat 
sensor removed.

8. Damage caused by any attachment or modification to the 
Water Heater, including any energy-saving device.

9. Damage caused by operation of the Water Heater at water 
temperatures exceeding the maximum rating, or if the water is 
not supplied with potable water.

10. Shipping charges, delivery expenses or administrative fees 
incurred by the purchaser in repairing or replacing the Water 
Heater.

CONDITIONS OF WARRANTY

The warranty herein is void under the following circumstances:

1. Failure or malfunction resulting from improper or negligent 
operation, accident, abuse, freezing, misuse, unauthorized 
alteration or improper installation, repair or maintenance.  See 
the Owner's Manual for installation and maintenance 
information.
2. Any Water Heater that is operated without a flame sensor rod 
or overheat sensor.
3. Any Water Heater that is used or operated in a corrosive 
atmosphere or at water temperatures exceeding the maximum 
rating, or if the Water Heater is not supplied with potable water.
4. Work performed without prior authorization or approval and 
without authorization/requisition number and without proper 
documentation verifying compliance with above terms.

LIMITED WARRANTY

OTHER THAN THE OBLIGATIONS OF BTC EXPRESSLY SET 
FORTH HERIN, BTC DISCLAIMS ALL WARRANTIES, EXPRESS 
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED 
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A 
PARTICULAR PURPOSE.  BTC'S SOLE OBLIGATION WITH 
RESPECT TO THE WATER HEATER AND PURCHASER'S 
EXCLUSIVE REMEDIES ARE SET FORTH IN THE FOREGOING 

Содержание 330-PN-L





































Отзывы: