Bosch 3 601 M23 600, Оригинальное руководство пользователя

Страница: 21 / 30

English | 37
Bosch Power Tools 1 609 92A 285 | (11.11.15)
– Place on the clamping flange 49 and the screw 48 .
Press the spindle lock 47 until it engages and tighten the
screw turning in anticlockwise direction.
– Release linkage 43 from fastening screw 45 and guide the
retracting blade guard down again.
– Slide cover plate 46 under fastening screw 45 again.
– Retighten the fastening screws 45 and 44 again.
– Slide linkage 43 onto its original position and retighten
locking screw 42 by hand again.
Operation

Before any work on the machine itself, pull the mains
plug.
Transport Safety (see figure A)
The transport safety-lock 31 enables easier handling of the
machine when transporting to various working locations.
Releasing the Machine (Working Position)
– Slightly push down glide arm 28 by handle 4 to release
transport safety-lock 31 .
– Pull the transport safety-lock 31 completely outward.
– Slowly guide the glide arm upward.
Securing the Machine (Transport Position)
– Slide glide arm 28 completely to the rear and secure it in
this position (see “Securing the Glide Arm”, page 37).
– Guide the glide arm downward until transport safety-lock
31 can be pushed completely inward.
For additional information on transport, see page 43.
Locking the Glide Arm
The glide mechanism of glide arm 28 can be locked with lock
lever 26 . Two glide arm positions are possible:
– Glide arm pushed completely to the rear (for chop-cuts)
– Glide arm pulled completely to the front (for a compact
transport position)
Releasing the Glide Arm (see figure B1)
After releasing the glide arm 28 , the complete pulling mecha-
nism is ready for operation.
– Push the lock lever 26 down to the stop.
The clamping wedge of the lock lever releases both bottom
joint parts of the glide arm.
Securing the Glide Arm (see figure B2)
Glide arm pushed completely to the rear:
– Push glide arm
28 toward the rear to the stop.
The two upper joint parts of the glide arm are now in the up-
right position and shut.
– Pull lock lever 26 upward until of the clamping wedge is po-
sitioned between the two bottom joint parts of the glide
arm.
This locks the completely pushed back glide arm
28 .
Glide arm pulled completely to the front:
– Pull glide arm
28 forward to the stop.
The glide mechanism is now completely extended.
– Pull lock lever 26 upward until of the clamping wedge is po-
sitioned between the two bottom joint parts of the glide
arm.
This locks the completely forward pulled glide arm
28 .
Preparing for Operation
Extending the Saw Table (see figure C)
Long workpieces must be underlaid or supported at their free
end.
The saw table can be extended left and right with the saw-ta-
ble extensions
11 .
– Push clamping lever 51 inward.
– Pull out saw-table extension 11 to the desired length (max.
250 mm).
– To lock the saw-table extension, push clamping lever 51
outward again.
Extending the Fence (see figure D)
For bevel angles, the fence extensions 9 must be moved.
– Turn clamping lever 52 toward the front.
– Pull the fence extension 9 completely outward.
– To lock the adjustable fence, push clamping lever 52 down
again.
Removing the Adjustable Fence (see figure E)
For extreme bevel angles, the fence extensions 9 must be re-
moved completely.
– Pivot cover plate 53 outward.
– Turn clamping lever 52 toward the front.
– Pull the fence extension 9 completely outward.
– Remove the fence extension upward.
Adjusting the Glide Movement (see figure F)
The glide mechanism of glide arm 28 is factory-preset, and
not set to glide movement upon delivery of the power tool.
The glide movement of the glide movement controller can be
individually adjusted on the controller
54 :
Hard – for more controlled work motion;
Soft – for fast saw cuts.
– For softer damping, loosen both set screws 55 using the
hex key (4 mm) 20
or
tighten both set screws 55 for harder damping.
Clamping the Workpiece (see figure G)
To ensure optimum working safety, the workpiece must al-
ways be firmly clamped.
Do not saw workpieces that are too small to clamp.
– Press the workpiece firmly against the fence 10 .
– Insert the material clamp 22 provided into one of the holes
56 intended for it.
– Loosen the wing bolt 57 and adapt the material clamp to
the workpiece. Tighten the wing bolt again.
– Firmly clamp the workpiece by turning the threaded rod
58 in clockwise direction.
OBJ_BUCH-1360-003.book Page 37 Wednesday, November 11, 2015 2:13 PM