Bosch 13-2, Оригинальное руководство пользователя

Страница: 14 / 87

14 | English
2 609 932 946 | (5.5.14) Bosch Power Tools
Technical Data
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-1.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, Germany
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, Germany
05.03.2014
Assembly
Auxiliary Handle (GBM 13-2/GBM 13-2 RE)
(see figure A)

Operate your machine only with the auxiliary handle
10.
The auxiliary handle 10 can be set to any position for a secure
and low-fatigue working posture.
Turn the bottom part of the auxiliary handle 10 in counter-
clockwise direction and swivel the auxiliary handle 10 to the
desired position. Then retighten the bottom part of the auxil-
iary handle
10 by turning in clockwise direction.
Adjusting the Drilling Depth
The required drilling depth X can be set with the depth stop
11 .
Press the button for the depth stop adjustment 9 and insert
the depth stop into the auxiliary handle 10 .
The knurled surface of the depth stop 11 must face down-
ward.
Pull out the depth stop until the distance between the tip of
the drill bit and the tip of the depth stop corresponds with the
desired drilling depth
X .
Changing the Tool

Before any work on the machine itself, pull the mains
plug.

Wear protective gloves when changing the tool. The
drill chuck can become very hot during longer work peri-
ods.
Keyless Chuck (see figure B)
Hold the rear sleeve 3 of the keyless chuck 1 tight and turn the
front sleeve 2 in rotation direction

, until the tool can be in-
serted. Insert the tool.
Hold the rear sleeve 3 of the keyless chuck 1 tight and firmly
tighten the front sleeve 2 by hand in rotation direction

, un-
Rotary drill GBM 10-2 RE GBM 13-2 GBM 13-2 RE
Article number 0 601 168 5.. 0 601 169 0.. 0 601 169 5..
Rated power input W 500 550 550
Output power W 270 285 285
No-load speed
– 1st gear
– 2nd gear min
-1
min
-1
0 – 1150
0 – 2100 1000
1900 0 – 1000
0 – 1900
Rated speed
– 1st gear
– 2nd gear min
-1
min
-1
0 – 800
0 – 1500
550
1000
0 – 550
0 – 1000
Rated torque (1st/2nd gear) Nm 9.5/5.0 11.5/6.0 11.5/6.0
Spindle collar dia. mm 43 43 43
Speed preselection

–

Speed control

–

Right/left rotation

–

Maximum drilling diameter (1st/2nd gear)
– Steel
– Wood
– Aluminium mm
mm
mm 10/6
25/15
13/8
13/8
32/20
20/12
13/8
32/20
20/12
Chuck clamping range mm 1 – 10 1 – 13 1 – 13
Weight according to EPTA-Procedure 01/2003 kg 1.7 1.9 1.9
Protection class /
II
/
II
/
II
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Henk Becker
Executive Vice President
Engineering Helmut Heinzelmann
Head of Product Certification
PT/ETM9
OBJ_BUCH-321-004.book Page 14 Monday, May 5, 2014 9:30 AM