Bosch 06039B6104, Оригинальное руководство пользователя

Страница: 15 / 199

English | 15
Drilling mode
When the setting ring (2) is set to the "drilling"
symbol, then the power tool is in second gear.
The operating mode indicator
(3) shows the
"drilling mode" symbol.
Use this setting for drilling in wood, metal or
plastic.
Impact drilling mode
When the setting ring (2) is set to the "hammer"
symbol, then the power tool is in second gear.
The operating mode indicator
(3) shows the
"drilling mode" symbol.
Use this setting for impact drilling in brick, ma-
sonry and stone.
Switching on/off
To start the power tool, press and hold the on/off switch
(11) .
The worklight (12) lights up when the on/off switch (11) is
lightly or fully pressed, allowing the work area to be illumin-
ated in poor lighting conditions.
To
switch off the power tool, release the on/off switch (11) .
Adjusting the Speed/Impact Rate
You can adjust the speed/impact rate of the power tool when
it is on by pressing in the on/off switch
(11) to varying ex-
tents.
Applying light pressure to the on/off switch
(11) results in a
low rotational speed/impact rate. Applying increasing pres-
sure to the switch increases the speed/impact rate.
Fully automatic spindle lock (Auto-Lock)
The drill spindle, and therefore the tool holder, are locked
when the on/off switch
(11) is not pressed.
This enables screws to be screwed in even when the battery
(10) is empty and allows the power tool to be used as a
screwdriver.
Run-out brake
Upon releasing the on/off switch (11) , the drill chuck is
slowed down, which prevents the application tool from con-
tinuing to rotate.
When driving in screws, you should therefore only release
the on/off switch
(11) once the screw has been inserted
flush into the workpiece. This way, the head of screw will not
penetrate the workpiece.
Battery charge-control indicator
When the on/off switch (11) is pressed in halfway or com-
pletely, the battery charge-control indicator (6) indicates
the charge condition of the battery for several seconds. The
indicator consists of three green LEDs.
The three LEDs of the battery charge indicator
(6) and the
lamp (12) flash quickly when the temperature of the battery
falls or rises outside the operating temperature range of -30
to +70 °C.
LED Capacity
3 × continuous green light 75–100 %
2 × continuous green light 40–75 %
1 × continuous green light 15–40 %
1 × slowly flashing green light 0–15 %
Temperature-dependent overload protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or the permitted bat-
tery temperature is exceeded, the electronics of the power
tool will switch off until the temperature returns to within the
optimum operating temperature range.
Protection against deep discharge
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Working Advice
u
Only apply the power tool to the screw when the tool
is switched off.
Rotating application tools can slip off.
After working at a low speed for an extended period, you
should operate the power tool at the maximum speed for ap-
proximately three minutes without load to cool it down.
Use carbide drill bits when working with concrete, stone and
masonry.
When drilling into metal, only use sharpened HSS drills (HSS
= high-speed steel) which are in perfect condition. The
Bosch accessory range guarantees appropriate quality.
Using the drill bit sharpener (accessory), you can effortlessly
sharpen twist drill bits with a diameter of 2.5–10 mm.
Maintenance and Service
Maintenance and Cleaning
u
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.
There is risk of injury
from unintentionally pressing the on/off switch.
u
To ensure safe and efficient operation, always keep
the power tool and the ventilation slots clean.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at:
www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Bosch Power Tools 1 609 92A 6UG | (14.07.2021)