background image

10/19

 

CH30T

 

 

                

Made in China to TQB Brands Pty Ltd specifications 

 

P a g e

 | 

1

 

Visit us at www.tqbbrands.com.au

 

WARNING INFORMATION 

 

 

 

 

IMPORTANT:  READ ALL INSTRUCTIONS BEFORE USE

  

 

 

 

    WARNING

  

The instructions and warnings contained in this manual should be read and understood before using or 
operating this equipment. Do not allow anyone to use or operate this equipment until they have read 
this  manual  and  have  developed  a  thorough  understanding  of  how  this  equipment  works.  Failure  to 
observe any of the instructions contained in the manual could result in severe personal injury to the user 
or bystanders, or cause damage to the equipment and property. Keep this manual in a convenient and 
safe place for future reference. 

The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible 
conditions and situations that may occur. It must be understood by the operator that common sense and 
caution are factors which cannot be built into this product, but must be supplied by the operator. 

Whilst every effort has been made to ensure accuracy of information contained in this manual, the Borum 
policy of continuous improvement determines the right to make modifications without prior warning. 

 

CONTENTS 

 

WARNING INFORMATION ................................................................................................................................................. 1 

CONTENTS ......................................................................................................................................................................... 1 

STANDARD OPERATING PROCEDURE ............................................................................................................................... 2 

ASSEMBLY, OPERATION, PREVENTITIVE MAINTENANCE .................................................................................................. 3 

PARTS LIST ......................................................................................................................................................................... 9 

PARTS DIAGRAM ............................................................................................................................................................. 10 

TROUBLESHOOTING ........................................................................................................................................................ 11 

WARRANTY...................................................................................................................................................................... 12 

 

 

Содержание CH30T














Отзывы: