background image

- 1 -

WILSONSTAK  LIBRARY and

CANTILEVER RECORD MASTER

 .

INSTALLATION INSTRUCTIONS

GENERAL INSTRUCTIONS:

1.  Check parts and bundles against packing slip to be sure all parts and bundles 

were received.

2.  Sort parts so that like parts are together.  This will make installation easier and 

faster.

3.  Read through the entire instructions carefully - before attempting to assemble 

the units.  

Units must be level.  

4.  Leveling - Units must be leveled (page 3).  Each type of welded frame requires 

a different procedure for leveling. 

5.  Anchoring - 

Important to prevent tip over of units.  Read and follow instruc-

tions for anchoring.  Anchoring must conform to building conditions and local 

codes.  Anchoring varies depending on heights and types of frames.  All single 

face units require wall anchoring, or floor anchors and top tie struts.  All units 78" 

and higher where adjustable shelves are vertically flush with base shelf require 

floor anchors or top tie struts.  (pages 5, 6 and 13).

6.  Loading - To ensure unit stability, units must be loaded starting at the base and 

working up.  Double face units should be loaded on both sides equally starting 

at the base and working up. 

WARRANTY
Borroughs Corporation extends to the original purchaser from the date of purchase a five-year limited warranty against manufacturing defects in material and workmanship.  If a Borroughs 

product fails to perform because of a manufacturing defect, Borroughs will examine it.  If found defective, it will be repaired or replaced at our option.  This warranty does not apply to 

any product which has been subject to misuse, negligence, or accident; has been damaged in shipment, storage, or installation; has been misapplied or has been modified or repaired 

by unauthorized persons or been repaired with non-standard Borroughs replacement parts.  This warranty specifically excludes claims for indirect, incidental, or consequential damages 

arising in any way from a product defect.  This warranty is exclusive, and exists in lieu of all other warranties, either expressed or implied.  To obtain warranty service, contact your Bor-

roughs Selling Dealer.  You must make a written claim.  Provide a copy of your purchase record and a written description of the warranty problem with your claim.  If you are unable to 

contact your Dealer, contact:  Borroughs Corporation, Customer Service Manager, 3002 N. Burdick St., Kalamazoo, MI  49004-3483.

IMPORTANT  -  PRODUCT LIABILITY INFORMATION

Read all instructions before proceeding with assembly.  Vital product 

information pertaining to proper set-up and cautions are included.

Failure to follow these instructions may result in personal injury and/or 

property damage.

IMPORTANT NOTICE - At no time should personnel be allowed to climb or stand on shelving product.  Safe access to all shelving levels 

should be provided with ladders and/or other devises which are in accordance with applicable OSHA regulations.

3002 N. BURDICK STREET  

  KALAMAZOO, MI  49004-3483

800-748-0227  

  FAX:  269-342-4161  

  www.borroughs.com

50-50424-000D

November 2016

®

®

Содержание WILSONSTAK





















Отзывы: