In this fully integrated appliance the controls are located on the
top of the door. When selecting a programme, the door needs
to be open.
1. Check that the baskets have been
loaded correctly and that the spray
arms can rotate freely
2. Turn on the water tap
3. Press the On/Off button
The indicator lights of the programme selection buttons
illuminate and in the digital display are visible 2 horizontal
lines (--).
4. Setting and starting the programme
To select a programme, press either one of the two
programme selection buttons, the indicator lights of the
programme selection buttons start to flash and the number
corresponding to the last performed washing programme
will appear in the digital display.
Using these two buttons you have an increasing (+) or a
decreasing (-) order in the selection of the programme
(see "Washing programmes" chart for the number of the
programme).
Example:
Button
(increasing order): 1
→
2
→
3 etc...
Button
(decreasing order): 1
→
9
→
8 etc...
If desired, select the half load option (if available with
the selected washing programme).
Close the dishwasher’s door, the programme will start
automatically.
Setting and starting the programme with the
delay start
Once the washing programme has been selected press the
Delay Start button, the corresponding indicator light will
illuminate and in the digital display appears 1h.
Press the delay start button until in the digital display will
appear the number of hours desired (from 1 hour up to 19
hours).
Close the dishwasher door, the countdown starts
automatically and will decrease with steps of 1 hour.
The opening of the door will not modify or interrupt the
countdown.
Once the delay start has elapsed the washing programme
will start automatically.
NOTE:
The start of the programme or the countdown of
the delay start will occur only after the closure of the door,
until this moment it is possible to modify the set made.
NOTE:
Once the washing programme has started, a point-
shaped optical signal appears on the floor beneath the
dishwasher’s door. This optical signal will remain
illuminated for all the duration of the washing programme.
If the appliance has been installed higher up with a
furniture door mounted flush, the optical signal will be no
longer visible.
5. To interrupt or cancel a washing
programme in progress
Interrupt or cancel a washing programme in progress
ONLY if it’s absolutely necessary.
Attention! Hot steam may escape when the door is
opened. Open the door carefully.
Interrupt a washing programme in progress
Open the dishwasher door; the programme will stop.
Close the door; the programme will start from the point at
which it was interrupted.
Cancel a washing programme in progress
Open the dishwasher door.
Press for about 3 seconds the Cancel button, the indicator
lights of the programme selection buttons will illuminate
and in the digital display will appear 2 horizontal lines (--)
indicating that the running programme has been cancelled
and that the machine has returned to setting mode.
(If a new washing programme is to be selected, check that
there is detergent in the detergent dispenser).
6. To cancel a delay start in progress
To cancel a delay start in progress you have to reset the
dishwasher; follow the same instructions given in "Cancel
a washing programme in progress". Cancelling a delay
start involves also the cancelling of the set washing
programme (and eventual options).
In this case you have to set the washing programme (and
options) again.
7. End of the washing programme
The dishwasher will automatically stop and an audible
signal informs you of the end of the washing programme.
When the washing programme has ended, the optical
signal on the floor beneath the dishwasher’s door will turn
off. Open the dishwasher door only when this optical
signal turns off.
Open the dishwasher’s door, leave it ajar and wait a few
minutes before removing the dishes; in this way they will be
cooler and the drying will be improved.
The End of cycle indicator light is illuminated.
Switch off the dishwasher by pressing the On/Off button.
8. Unloading the dishwasher
Hot dishes are sensitive to knocks. The dishes should
therefore be allowed to cool down before removing from
the appliance.
Empty the lower basket first and then the upper one; this
will avoid water dripping from the upper basket onto the
dishes in the lower one.
Water may appear on the sides and the door of the
dishwasher as the stainless steel will eventually become
cooler than the dishes.
When the washing programme has finished, it is
recommended that the dishwasher is unplugged and the
water tap turned off.
Starting a washing programme
35
