Booster NBO Скачать руководство пользователя

Страница: 3 / 36

Chapter 3 Manipulation of the Auxiliary Equipment

3-1 Manipulation Method ---------------------------------------------------------------------------12

(1) Setting Method for the Thermal Relay of the Magnetic Switch(OCR) ------------ ------- 12

(2) Adjusting Method for the Pressure Switch -------------------------------------------------- 13

(3) Air Extraction for the Feed Water Pump ---------------------------------------------------- 13

(4) Air Extraction Method for the Oil Heater --------------------------------------------------- 13

(5) Pressure Adjusting Method for the Oil Pump ----------------------------------------------- 13

(6) Wiring Method for the Feed Water Pump and the Oil Pump ------------------------------ - 14

(7) Capacity Adjusting Method (Damper Blade) -------------------------------------------------- 14

(8) Adjusting Method for the Water Level Control Equipment ------------------------------- 16

(9) Concentration Blowing-off Device ------------------------------------------------------------17

(10) Operation status for Combustion Control(Protect Relay) --------------------------------18

3-2 Brief Maintenance Check and Cleaning Method --------------------------------------------- 19

(1) Check for the Soft Water ---------------------------------------------------------------------- 19

(2) Check for the Concentration Blowing-off Device ------------------------------- -----------20

(3) Check and Cleaning for the Oil Strainer ----------------------------------------------------- 20

(4) Check and Cleaning for the Oil Heater Strainer -------------------------------------------- 20

(5) Check and Cleaning for the Feed Water Strainer and the Concentration

Blowing-off Strainer ---------------------------------------------------------------------------- 21

(6) Check and Cleaning for the Water Level Electrode Bar ----------------------------------- 21

(7) Check and Cleaning for the Oil Pump -------------------------------------------------------- 21

(8) Check for the Safety Valve --------------------------------------------------------------------- 22

(9) Check and Cleaning for the Burner ----------------------------------------------------------- 22

(10) Cleaning for the Returning Water Tank and Check for the Ball Tap --------------------- 24

(11) Cleaning for the Oil Tank ----------------------------------------------------------------------- 24

Chapter 4 Safety Device

-1 Superheating Prevention for the Boiler Main Body ------------------------------------- 24

(1) Burner Operation Suspension at the Low Level -------------------------------------------- 24

(2) Superheating Prevention Switch -------------------------------------------------------------- 25

4-2 Freezing Prevention ------------------------------------------------------------------------------- 25

Содержание NBO





































Результаты поиска

Содержание NBO

Отзывы:

Похожие инструкции для NBO

Бренды по названию

Популярные бренды

Booster NBO, Руководство по эксплуатации

Результаты поиска

Содержание NBO

Отзывы:

Похожие инструкции для NBO

Бренды по названию

Популярные бренды