1
3
2
4
5
6
9
7
8
10
Sensor Activation:
Verify proper magnet install and spin wheel or turn crank more than
two revolutions. Initial sensor activation and magnet alignment will be indicated by the
LEDs flashing up to 10x.
Please Note:
The sensor will stay active for at least 2 minutes although the LEDs no
longer flash.
Bluetooth Smart Connection:
Install and activate sensor. Turn on your phone’s (or other
compatible device) Bluetooth capability. Please note, Bluetooth Smart devices do not
always appear in your phone’s listing even when connected. Open the desired cycling app
and follow instruction for Bluetooth Smart sensor connection. All apps collect, share, and
display speed and cadence information differently.
FR
—La diode Rouge clignotera lorsque l’aimant vitesse est en cours d’appairage. La
diode Verte clignotera lorsque l’aimant cadence est correctement appairé. Ces lumières
clignoteront seulement durant les 10ers tours de roue.
DE
—Die rote LED blinkt, wenn der Tacho-Magnet korrekt ausgerichtet ist. Die grüne LED
blinkt, wenn der Trittfrequenz-Magnet korrekt ausgerichtet ist. Beides erfolgt nur während
der ersten 10 Umdrehungen von Kurbel bzw. Laufrad.
ES
—El LED rojo emitirá destellos cuando el imán de la velocidad esté correctamente
alineado. El LED verde emitirá destellos cuando el imán de la cadencia esté correctamente
alineado. Los LEDs emitirán destellos sólo durante las diez primeras revoluciones.
3-5mm
Interchange Combo Sensor
sensor
mounting strap
Speed Magnet
(wheel)
cadence magnet
(crank)
Place sensor on non-drive side
chainstay with logo facing out.
Pull mounting strap over hook,
or use zip ties if necessary. Note:
remove wheel to ease installation.
Align cadence band with
marking on sensor.
Adjust sensor speed arm within 3-5mm of sensor and tighten with a
2mm hex.
LED indicators will flash upon
activation by two complete pedal
strokes.
Adjust sensor so distance is
3-5mm from cadence band.
Speed magnet.
Align speed magnet with marking
on sensor and tighten on spoke.
Replacement battery CR2032.
Attach mounting strap or zip ties.
Install cadence magnet on
non-drive side crank arm with
logo facing out. Pedal will need
to be removed for this step.
BATTERY REPLACEMENT
2Nm
2mm
3-5mm
Statements of Regulatory
Compliance
FCC Compliance
Interchange Digital Combo Sensor
FCC ID: 04GTKCOMBO
This device complies with part 15 of the FCC Rules. Operation is subject
to the following conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
This product may cause interference to radio equipment and should not be
installed near maritime safety communications equipment or other critical
navigation or communication equipment operating between 0.45-30 MHz.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or experienced radio / TV technician for help.
