Bona MiniEdge Скачать руководство пользователя страница 15

Страница: 15 / 18

Bona MiniEdge

Trouble shooting

Fault

Cause

Action

The machine doesn’t start

No power.

Change to another wall socket.

Cable broken.

Change the cable.

Rotation of the disc is impossible

Rotate the sanding disc, remove
possible blockages.
Check that the ventilator runs
smoothly.
Adjust the ventilator.

The sanding disc doesn’t
rotate

The cogged belt is broken/worn
out.

Change the cogged belt.

The machine is faltering

The carbon brushes are worn
out.

Change the carbon brushes.

The carbon brackets are broken.

Change the carbon brushes.

The carbon brushes are binding.

Clean the carbon brush channel.

Big blue sparks in the motor

Short-circuit at the carbon
brushes.

Change the carbon brushes or
perhaps the armature.

The machine is vibrating
heavily

Off centre sanding disc.

Centre the disc.

Ventilator damaged.

Change ventilator.

Object stuck in the pulley.

Clean the pulley.

Uneven sanding

Badly adjusted wheels.

Adjust the wheels.

Unevenly worn wheels.

Change the wheels.

The wheels are binding.

Clean or change the wheels.

The sanding disc is loose.

Fix or adjust the disc.

Object between sanding disc and
plate.

Clean.

Binding sanding disc.

Change the velcro disc or tighten
the centre screw.

The lamp is not working

The lamp is damaged.

Change the lamp.

The lamp is loose.

Fix the lamp in the socket.

Содержание MiniEdge



















Результаты поиска

Содержание MiniEdge

Отзывы:

Похожие инструкции для MiniEdge

Бренды по названию

Популярные бренды

Bona MiniEdge, Руководство пользователя

Результаты поиска

Содержание MiniEdge

Отзывы:

Похожие инструкции для MiniEdge

Бренды по названию

Популярные бренды