background image

- 12 - 

General regulations 

  Apart  from  this  manual,  one  shall  also  follow  traffic  regulations  and  occupational 

safety and health regulations. 

  Warnings  (pictograms)  placed  on  the  ridger  give  advice  concerning  safety  of  the 

user and other people, and avoiding accidents. 

  When  driving  on  public  roads,  it  is  obligatory  to  follow  regulations  included  in 

Highway Code. 

  It is recommended to cooperate with a tractor equipped with a cabin or a protective 

frame. 

  Before each using the machine, it is necessary to check if all elements of the ridger 

are in a good condition. Damage incurred shall be fixed without delay and possible 
deficiencies filled up. 

  Avoid staying within the range of the operating ridger. 

  Before  leaving  the  tractor  cabin  and  before  each  activity  made  at  the  ridger,  stop 

the tractor engine and remove the key from the ignition switch. 

  The  ridger  shall  be  stored  in  a  dry  room,  on  the  tough  and  flat  ground.  During 

lowering the ridger onto the ground, keep particular caution. Danger of injury!!! 

Aggregation 

  Keep  particular  caution  during  connecting  the  ridger  with  a  tractor  and  during 

disconnection. 

  It  is  forbidden  to  stay  between  the  ridger  and  a  tractor  during  any  activities 

performed with a hydraulic system lever. 

  While aggregating the  ridger with a tractor, it  is forbidden to stay between the  tool 

and the tractor at the tractor engine working.  

  During performing any maintenance at the ridger, it is necessary to stop the engine, 

remove the key from the ignition switch and pull the handbrake. 

  Pivots of the ridger suspension system shall be secured only with the use of typical 

protection in the form of cotter pins. 

  The  ridger  shall  be  aggregated  only  with  recommended  tractor  classes  equipped 

with front axle standard ballasts. 

  The  ridger  can  be  operated  by  a  person  with  qualifications  allowing  for  using 

agricultural tractors. 

  During aggregation, keep the minimum load of the tractor front. 

 

CAUTION  

Operation with a tractor of another class than recommended by  
the manufacturer may cause threat of stability loss in operation or in stoppage.  
The load of the tractor’s front axle cannot be lower than 20% of its weight.

 

 

Maintenance 

  A  ridger  can  be  operated  by  a  person  with  qualifications  allowing  for  using 

agricultural tractors and acquainted with the manual of the ridger. 

  It  is  not  allowed  for  other  people  not  acquainted  with  the  manual  to  operate  the 

ridger. 

  It is not allowed for children and people after drinking alcohol to operate the ridger. 

  The  ridger  shall be  raised  onto  the  tractor  suspension  system  easily,  without  jerks 

or vibrations. 

  Raise the ridger upwards each time when turning and making returns. 

  At  each  getting  off  the  tractor  by  the  operator,  leave  the  ridger  in  the  lowered 

position. 

Содержание Norma P-475/1































Отзывы: