Bomag BW 100 ACM-5 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 176

background image

Safety regulations

BOMAG

40

BW 80 AD-5 Fam.

Lift the machine only with suitable lifting gear. Use only safe lifting gear of suf-
ficient load bearing capacity Minimum lifting capacity of lifting gear: see oper-
ating weight in chapter "Technical Data".

Do not lift or lower the machine jerkily.

The tension must always be effective in vertical direction.

The machine must not swing about when being lifted.

Do not step or stand under suspended loads.

Lashing

Always use suitable lashing gear on the lifting points to lash down the ma-
chine.

Check all lashing points for damage before lashing down the machine. Do not
use a damaged or in any other way impaired lashing points.

Always apply the articulation lock for transportation.

Lash the machine down, so that it is secured against rolling, sliding and turning
over.

After transport

Operate the machine only with the foldable ROPS

1

properly fastened and the

fastening screws tightened with the correct tightening torque.

After transport release the articulation lock again and store it in the receptacle.

Towing the machine

Apply appropriate measures (e.g. with metal wheel chocks, to be provided by
the operating company) to secure the machine against rolling away before re-
leasing the parking brake.

Use a tow bar (tobe provided by the operating company).

Use a towing vehicle with sufficient traction and braking power for the un-
braked towed load.

The machine cannot be steered.

Tow the machine only after having released the parking brake.

Max. towing speed 1 km/h (0.6 mph), max. towing distance 500 m (0.3 mi).

1

Optional equipment

«
...
38
39
40
41
42
...
»

Содержание BW 100 ACM-5

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BW 100 ACM-5

Бренд: MAHLE Страницы: 21

Бренд: York Fitness Страницы: 34

Бренд: Rain-Flo Irrigation Страницы: 20

PELTOR WS LiteCom Plus

Бренд: 3M Страницы: 7

Бренд: BACtrack Страницы: 16

Бренд: ICP DAS USA Страницы: 45

Бренд: Idex Страницы: 141

Бренд: IDEAL Networks Страницы: 8

Бренд: IDEAL Networks Страницы: 5

Бренд: Madsen Страницы: 206

Бренд: Naked Страницы: 36

Бренд: Pari Страницы: 11

Бренд: Pari Страницы: 2

Бренд: Haas Страницы: 5

Бренд: Yamaha Страницы: 139

Бренд: Yamaha Страницы: 19

Бренд: Yamaha Страницы: 32

Бренд: Garmin Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды