Bolt VB-11 Скачать руководство пользователя | Manualshive

Страница: 17 / 36

background image

Mounting the Flash

|

17

Mounting the Flash on a Shoe or Stand/Tripod Mount
1. If using a VB-22, ensure that the Shoe Mounting Foot is

securely installed.

2. With the unit turned off, loosen the tightening ring on

the mount.

3. Slide the unit into the shoe.
4. Secure the flash by turning the tightening ring

clockwise.

Mounting the Flash on a Stand
1. Holding either the Stand/Tripod Mount or the VB-22

with the Stand Mounting Foot securely installed, place
the threaded socket over the stand’s ¼”-20 installation
screw.

2. Screw in the Stand/Tripod Mount or VB-22 by turning it

clockwise until tight and secure.

3. If using the Stand/Tripod Mount, follow the steps above

to mount the flash on the foot.

«
...
15
16
17
18
19
...
»

Содержание VB-11





































Отзывы:

Нет отзывов

Похожие инструкции для VB-11

Бренд: Olympus Страницы: 43

Бренд: Tachyon Страницы: 13

Бренд: Olympus Страницы: 1

PowerShot ELPH 110 HS

Бренд: Canon Страницы: 218

Бренд: Panasonic Страницы: 314

PowerShot ELPH 510 HS

Бренд: Canon Страницы: 212

FE110 - 5 Megapixel Digital Camera

Бренд: Olympus Страницы: 2

Бренд: Olympus Страницы: 75

Бренд: Zavio Страницы: 108

.WDR Camera Series

Бренд: Digital Equipment Страницы: 10

UltraZoom C-2100U

Бренд: Olympus Страницы: 146

Бренд: Clas Ohlson Страницы: 36

Бренд: Zavio Страницы: 16

Бренд: Geutebruck Страницы: 148

Бренд: Hyundai Страницы: 13

Princeton Instruments Nano-XF

Бренд: Teledyne Страницы: 56

Бренд: Brickhouse Security Страницы: 18

Бренд: MIRABELLA Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды