bolid SIGNAL-20P Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 57

background image

INTRUSION&FIRE ALARM ADDRESSABLE 20-LOOP CONTROL DEVICE

48

c) Verify the device useful current being not exceeded values pre-

sented by the Table 1.

d) Verify the S2000/S2000M console displaying the occurring events,

such as:

- “RST RS485 LINE” in case of device has been detected
- “DEVICE RESTART” in case of device reset
- “TAMPER ALARM” when device case is opened

6.1.2 Testing in diagnostic mode

Before diagnostic

disconnect all relay load circuits

!

To run the diagnostic mode open the device cover and press tamper

detector three times for short time (0,1-0,5 s) and once hold for a time at
least 1,5 s. The pause between pressings shall be no more than 0,5 s.

The device being useful, the “Ready” indicator should enter the inter-

rupted quick flashing light mode with the frequency of 2 Hz.

Then all relay outputs shall switch off and loop voltages shall cut out

for 3 s.

After loop voltage having recovered the relays from 1 to 5 in turns

shall switch on and off with the interval of 2 s.

As soon as relay 5 has been switched off the outputs “K” and “

З

”

shall be supplied for 2 s.

After outputs “K” and “

З

” having been switched off the device auto-

matically exits out of diagnostic mode and returns into the operating mode.

6.1.3 Alarm loop checking

а

) The alarm loop being disconnected (terminal resistor being dis-

connected), measure the first alarm loop voltage. It shall be within the
range from 26,5 to 27,5 V.

b) Connect the terminal resistor 4,7 k

О

hm to the “

ШС

1” and read the

ADC value by means of S2000/S2000M as follows:
- Select the menu commands “Request INFO” and "Zone ADC"
gradually
- Enter the device address (the default value is 127) or select the
device descriptor from the list of connected devices with the help of
"

t

" and "

u

" keys

- Enter the alarm loop number 1
The value given out shall be within the range from 46 to 50.

c) Repeat the steps from b) item for loops from 2 to 20.

«
...
46
47
48
49
50
...
»

Содержание SIGNAL-20P


























































Отзывы:

Нет отзывов

Похожие инструкции для SIGNAL-20P

Бренд: Panasonic Страницы: 45

Бренд: Wavelink Страницы: 69

Бренд: BADODOSECURITY Страницы: 8

Бренд: Samson Страницы: 52

Бренд: WAREMA Страницы: 112

Бренд: WAGO Страницы: 414

Бренд: V2 Страницы: 48

Бренд: Xilinx Страницы: 2

Бренд: Saluki Страницы: 13

GA Industries 930-DT

Бренд: Vag Страницы: 4

ArtNet-DMX Mux16

Бренд: DMX4ALL Страницы: 21

Red Atom PETRA01

Бренд: Perenio Страницы: 24

Бренд: QUICK DAM Страницы: 16

SR-ZG9001T-RGBW

Бренд: Sunricher Страницы: 3

Бренд: phytron Страницы: 55

Бренд: B meters Страницы: 2

Бренд: Samson Страницы: 36

SCENE MASTER - V1.0

Бренд: JBSYSTEMS Light Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды