background image

 

1

BATTERY BACKED POWER SUPPLY

 

RIP-12 mod.14 

(RIP-12-2/7P2-R) 

 

INSTRUCTION MANUAL 

1

 

TECHNICAL DATA 

1.1

 

General 

1.1.1

 

The  battery  backed  power  supply  RIP-12  mod.14  (RIP-12-2/7P2-R)  (hereinafter 

referred  to  as  the  RIP)  is  intended  to  provide  continuous  operating  power  to  a  group  of 
detectors  and  control  and  indicating  equipment  in  fire  alarm  systems,  security  systems, 
access control systems as well as to other appliances that require backed power of 12 V dc. 

1.1.2

 

The RIP provides round-the-clock operation with specified output parameters and 

automatic monitoring and recharging of the sealed backup battery (hereinafter referred to as 
the battery). The RIP provides shutting off the battery from a load to avoid its unacceptable 
discharge

.

 

1.1.3

 

The  RIP  provides  protecting  its  output  against  short  circuit  failures  with 

recovering  output  voltage  automatically  after  repairing  the  failures  as  well  as  protection 
against output overvoltage. 

1.1.4

 

The RIP provides protection against short circuit failures of battery leads keeping 

the output voltage stable if the RIP operates from mains power. 

1.1.5

 

The  RIP  provides  light  and  sound  indication  of  current  conditions,  including 

presence or absence of mains power voltage, the battery charge, a short circuit failure or an 
overload at the output, missed battery, shutting the battery off in case of its discharge as well 
as indication of possible RIP faults during operation (see Table 2). 

1.1.6

 

The RIP provides limiting of the battery charger voltage and current depending on 

the temperature within the device enclosure. 

1.1.7

 

The  RIP  provides  monitoring  battery  conditions  and  its  connecting  circuit  (by 

comparing with maximum admissible internal resistance of this circuit). 

1.1.8

 

The  RIP  design  does  not  imply  using  this  power  supply  in  explosion-hazardous 

premises. 

1.1.9

 

In  terms  of  environmental  conditions,  the  RIP  complies  with  the  climatic 

modification  ‘

УХЛ

’  (NF,  for  temperate  and  frigid  climate  zones)  and  the  arrangement 

category  3  as  per  GOST 15150-69  but  for  operation  at  the  temperature  range  263 ÷ 313 

К

 

(minus 10 t40°

С

) and relative humidity up to 90 % at 298 

К

 (+25 °

С

). 

1.1.10

 

In terms of resistance to mechanical exposure, the RIP meets the requirements of 

the arrangement group ‘LX’ as per GOST 12997-84 withstanding vibrations in the frequency 
range 1 through 35 Hz at 4.9 m/s

2

 (0.5 g) acceleration. 

1.2

 

Specifications 

1.2.1

 

The main power supply is the mains power 150 V to 250 V, 50 Hz. 

1.2.2

 

The  backup  power  supply*  is  a  Delta  battery  DTM1207  (12 V,  7 Ah)  or  similar 

one with equivalent parameters (with battery life at least 5 years). 

 

*

The battery to be supplied separately.

 

1.2.3

 

The rated output voltage while powered by mains is (13.6

±

0.6) V. 

1.2.4

 

The low battery shutdown voltage is (10.2

±

0.6) V. 

1.2.5

 

The rated load current is 2 A. 

Содержание RIP-12









Отзывы: