Bogen NYQUIST NQ-A4060 Скачать руководство пользователя страница 41

Страница: 41 / 42

To view status for the power amplifier:

Step 1

On the appliance Web UI’s main page, select

DSP

Step 2

Select the

Menu

button for the channel.

From the drop-down menu, select

Status

The view only information that appears is described in the following

table:

Table 13, Status

Switch Position

Indicates the position of the Amplifier Mode

switch located on the rear of the appliance.

Bridged mode is typically used when higher

power, single channel operation with a high

impedance loudspeaker load is needed. For

information about setting the Amplifier

Mode, refer to the installation manual for the

appliance.

Thermal Protect

Appears red if the equipment has become

too hot and has placed itself into protection

mode. Otherwise, the LED is green.

Channel 1 Output
Limit

Appears red if the output signal is being

clipped or distorted. Otherwise, the LED is

green.

Channel 2 Output
Limit

Appears red if the output signal is being

clipped or distorted. Otherwise, the LED is

green.

Temperature

Provides the real-time temperature of the

appliance in both Celsius and Fahrenheit.

Содержание NYQUIST NQ-A4060










































Результаты поиска

Содержание NYQUIST NQ-A4060

Отзывы:

Похожие инструкции для NYQUIST NQ-A4060

Бренды по названию

Популярные бренды

Bogen NYQUIST NQ-A4060, Руководство по настройке

Результаты поиска

Содержание NYQUIST NQ-A4060

Отзывы:

Похожие инструкции для NYQUIST NQ-A4060

Бренды по названию

Популярные бренды