background image

ECO-SERIES REAR BUMPER 2007-2016 CHEVY 

SILVERADO\GMC SIERRA 1500

 

  

PARTS LIST: 

1  LD1 Rear Bumper Assembly 

4  12-1.75mm x 35mm Hex Bolts

1  Driver/left Frame Bracket 

8  12mm x 37mm OD x 3mm Flat Washers 

1  Passenger/right Frame Bracket 

4  12mm Nylon Lock Nuts 

1  License Plate Light 

2  10-1.5mm x 50mm Hex Bolts

2  License Plate Plugs 

4  10mm x 34mm OD x 3mm Flat Washers 

4  Sensor Hole Plugs 

2  10mm Nylon Lock Nuts 

1  Trailer Plug Bracket 07-13 

2  6mm x 16mm Hex Bolts 

1  Trailer Plug Bracket 2014+ 

4  6mm ID x 12mm OD x 1.6mm Flat Washers 

10  Nylon Wire Ties 

2  6mm Nylon Lock Nut 

6  14-2.0mm x 45mm Hex Bolts

1  4mm Allen Wrench 

12  14mm x 28mm OD x 2.5mm Flat Washers 

8  4mm x 10mm Button Head Bolts 

6  14mm Nylon Lock Nuts 

 

 

PROCEDURE: 

 

REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS 

CAREFULLY BEFORE STARTING INSTALLATION. BUMPER IS HEAVY, ASSISTANCE IS HIGHLY 

RECOMMENDED TO AVOID POSSIBLE INJURY OR DAMAGE TO THE VEHICLE.   

1.

Remove the license plate. On models with bumper sensors, unplug all sensors. Remove the trailer plug

from the bumper. Release the wiring harness from the clips attached to the back of the bumper and

move harness away from bumper as necessary.

2.

Place blocks or jack stands under the bumper to support it during mounting bolt removal.

3.

Determine procedure for your model year:

07-13 Models.

a.

Starting on the passenger/right side, remove (2) hex bolts attaching bumper to top/center of

receiver hitch if equipped.

b.

Remove hex bolts from side and bottom of frame, 

(Figures 1—3)

.

c.

Repeat previous Steps to remove driver/left side hardware.

d.

With assistance, pull bumper and brackets straight out from vehicle, 

(Figures 6 & 7)

.

14-16 Models.

a.

Starting on the passenger/right side, remove rear bolts attaching bed to frame, 

(Figure 2)

.

Loosen center bolts (if equipped). Do not loosen front bolts.

b.

Remove hex bolts from side and bottom of frame, 

(Figures 1—3)

.

c.

Repeat previous Steps to remove driver/left side hardware.

License Plate Light 

(4) Sensor

Hole Plugs

(2) Plastic Nuts for License Plate

Passenger/right 

Frame Bracket 

Driver/left 

Frame Bracket 

2014-on Trailer 

Plug Bracket 

2007-13 Trailer 

Plug Bracket 

Содержание ECO Series








Отзывы: