11. SETTING THE TIME AND DATE.
The time and date are factory set so it will not normally be necessary to do this on site. Changes between summer and
winter time are handled automatically by the unit.
1. Switch the slider to
Time
/
Date
. The hour symbols will flash, use
+
or
–
to adjust.
2. Press the
Next
button and the minute symbols will flash, use
+
or
–
to adjust.
3. Press the
Next
button and the day date will flash, use
+
or
–
to adjust the day.
4. Press the
Next
button and the month date will flash, use
+
or
–
to adjust the month.
5. Press the
Next
button and the year date will flash, use
+
or
–
to adjust the year.
6. Press the
Next
button and choose between 12hour or 24hour clock by using the
+
or
–
buttons.
7. Press the
Next
or
Home
button or wait for 15 seconds to automatically confirm and return to Run mode.
12. USING THE COPY FUNCTION.
The unit is provided with a copy function which allows an adjusted programme to be copied to another day or set of
days. This avoids the necessity of re-entering a desired programme for another day or sets of days.
N.B. This function only works in 7 Day setting.
To operate the copy function
1. Switch the slider to
PROG
and press the
Home
button.
2. Press the
C
button to enter the
COPY
mode.
3. The
A
button chooses the day you want to copy from (day not flashing) and the
+
/
-
buttons choose the day you
want to copy to (flashing).
4. Press the
C
button to confirm. The screen will show
SEr
(to show the Copy function is set).
13. BATTERY REPLACMENT.
When the low battery symbol flashes in the LCD display, the batteries need to be replaced as soon as possible.
The battery compartment is located on the front of the thermostat, under the fascia cover. Remove the old batteries
and insert new ones. All settings including time are maintained.
N.B. If the display ever goes blank during normal operation, the batteries need to be replaced with high quality alkaline
cells. The date, time and factory pre-set heating times will be retained (assuming the backup battery in the back of the
thermostat has not failed).
14. RESETTING THE UNIT.
To reset the programmer to the default settings
–
1. Switch the slider to
OFF
.
2. While holding in the
Next
button press and hold in the
reset
button
for approx. 3 seconds.
3. Release the
reset
button while still holding in the
Next
button.
4. Now release the
Next
button.
The programmer will now reset to factory defaults with the time and date needing to be reset.
SECTION 2
– INSTALLATION AND MASTER SETTINGS
15. INSTALLATION SAFETY INSTRUCTIONS.
Installation Safety Instructions
•
The unit must be installed by a suitably qualified person in accordance with the latest IEE Wiring Regulations.
•
Isolate mains supply before commencing installation.
•
Please read all instructions before proceeding.
•
Ensure that the fixed wiring connections to the mains supply is via a fuse rated at not more than 6 amps and class
‘A’ switch having a contact separation of a minimum of 3mm in all poles.
•
The recommended cable sizes are 1.0mm² or 1.5mm².
•
No earth connection is required as the product is double insulated but ensure continuity of earth throughout the
system.
General Safety Instructions
When fitting batteries, do not mix old and new batteries together. Do not use rechargeable batteries.
This product complies with the essential requirements of the following EC Directives:
•
Electro-Magnetic Compatibility Directive 2014/30/EU
•
Low Voltage Directive 2014/35/EU
•
EC Marking Directive 93/68/EEC
Please leave the user instructions with the end user where they should be kept in a safe place for further reference.
Maintenance
Always isolate the mains supply before commencing any work, servicing or maintenance on the system. And please
read all instructions before proceeding.
5
