background image

Service Manual for RESmart

®

 Auto CPAP V1.1 

3/16 

 

Power on the RESmart

®

 Auto CPAP device. If the device is power on from beginning, please power 

off the device and turn on again after 5 seconds more. 

4.  After the device is turned on, the following will display: 

 

Click 

Upgrade

 to start. If success, the right version number will be displayed on RESmart

®

 Auto 

CPAP device screen when every power on. 

Note: 

If failed during upgrading, please repeat from above 1-4 steps. 

If 

Error 08

 displayed after software upgrading, it means unmatched software used (for example: 

apply RESmart

®

 Auto CPAP software to RESmart

® 

CPAP device). In this case, apply correct software 

and upgrade again. 

3.2 Hidden Function 

1. 

Humidifier matching and dis-matching 

(Available on version 1.19 and later) 

Assemble humidifier on main device, without water chamber. Enter the maintenance menu, and set 
Ramp=40, then press Heated Humidifier Button when the Init P appears. Thus the humidifier is 
matched. When ‘OK’ appears on screen, humidifier matching succeeded. 

If cut the power supply after pressing ‘Pressure Start/Stop Button’ when the humidifier is matching, 
the humidifier will be dis-matched. 

2. 

Reset 

(Available on version 1.28 and later) 

Press and hold the Ramp Button until the user menu appears (about 3 seconds) when the device is 
on standby, press +/- User Buttons to access the Date Setting, set ‘YYYY/MM/DD’=’2097/07/01’, 
then press ‘Pressure Start/Stop Button’ when ‘Hour’ setting appears, thus all device settings and 
therapy records (doesn’t include Use Days and Use Time) will be reset. 

If set ‘Minute’=’16’ during the above procedure, then not only device settings and therapy records, 
but also patient information will be reset. 

If set ‘Minute’=’26’ during the above procedure, then not only device settings, therapy records and 
patient information, but also Use Days and Use Time will be reset. 

3. 

Pressure calibration

 (Available on version 1.58 and later) 

Connect pressure meter to the air outlet of the device, in the Date and Time Setting menu, set 

Содержание RESmart Auto CPAP




















Отзывы: