P/N 033000=13610 Rev. 01-02-06 BMB Home Security
15
It’s advisable to write down which zone contains which sensor. There’s space reserved at the back of this user
manual.
6. Repeat step 5 for every motion detector you wish to register.
7. Press CLEAR again to quit the menu. To confirm your choice, press 1 for Yes or 2 for No. If you choose Yes,
you will quit the menu. If you choose No, you go back to the first menu item. .
4.3 Additional (Wireless) Emergency Sensors (*OPTIONAL)
The Additional (Wireless) Sensor make sure you are warned in case of an emergency. When you’re at home,
the built-in siren will be triggered. Combined with your security system the internal siren, the telephone dialler
and the lights will be activated. This gives you an optimal warning and makes sure your exits are well lit. If you
are away from home, you will receive a warning via your mobile phone.
The telephone message indicates that an Emergency Sensor has been triggered and that it is not the burglar
alarm. This is done by adding an extra message to your own spoken telephone message. This standard multi-
lingual message is pre-programmed into your system.
4.3.1 Registering the Additional (Wireless) Sensor with the Console
1. To access the menu, press the menu UP or menu DOWN ?
button. The display now shows
ENTER PIN.
2. Enter your 4-digit PIN code (factory setting 0000. See 8.3 for changing the PIN code). The display is cleared
and shows a * for each number entered.
3. When the PIN code has been entered correctly, the word
INSTALL
will show up on the display.
4. Press OK.
5. Insert the batteries into the detector (see the user manual of the additional sensor for more information). The
console will beep to confirm. The display will read
RMOT 3 SET
or
ZONE …’. SET
.
The Additional (Wireless) Sensor works most likely the same as a remote control (panic function). It will make
sure the security system will call you, even if the system is not activated. Other option is the function of a D/W
sensor. If you have one or more remote controls or additional sensors installed, the display will read e.g.
RMOT 4
SET, RMOT 5 SET, … RMOT 16 SET
or
ZONE 2 SET, ZONE 3 SET, … ZONE 30 SET
. You can register up to 16 remote controls
and/or additional panic detectors based on remote panic function, or up to 30 sensors in case of wireless alarm
sensor function.
6. Repeat step 5 for every additional sensor you wish to register.
7. Press CLEAR to go back to the first menu item. Press CLEAR again to quit the menu.
If required you can remove Additional (Wireless) Sensors from the memory. This method is described in 8.2.
All information on mounting the respective detector can be found in the user manual of the respective detector.
4.4 Thermostat TS10 DigiMax210 (*OPTIONAL)
The DigiMax210 is available separately. Please visit
www.bmb-home.com
for more information.
4.4.1 Registering a Thermostat
1. To access the menu, press the menu UP or menu DOWN ?
button. The display now shows
ENTER PIN.
2. Enter your 4-digit PIN code (factory setting 0000. See 8.3 for changing the PIN code). The display is cleared
and shows a * for each number entered.
3. When the PIN code has been entered correctly, the word
INSTALL
will show up on the display.
4. Press OK. The display will read
INSTALL ZONE
.
5. Set the Thermostat to registering mode (see respective manual). The console will beep to confirm. The
display will read
THST…’. SET
. ?
If you have more than 1 thermostat installed, it will show e.g.
THST 2 SET, THST 3 SET, …
THST 4 SET
.
6. Repeat step 4 for every Thermostat you wish to register (up to 4).
7. Press CLEAR again to quit the menu. To confirm your choice, press 1 for Yes or 2 for No. If you choose Yes,
you will quit the menu. If you choose No, you go back to the first menu item.
?
4.4.2 Use of the TS10 Thermostats
The RF DigiMax210 Wireless thermostat does not need any extra wiring and works within 30 meters range. It is
equipped of a secured RF code which the SC28 Base Console will learn during the installation process. This
code will assure that the Security Base Console or Home Controller will only answer to messages sent by your
DigiMax210. You can connect up to 4 DigiMax210 to the Maxi Controller. Depending on the information sent by
the thermostats, the SC28 Base Console will send X10 Home Automation Messages on the power line to turn
On or Off X10 modules connected to your heaters or boiler. Besides heating the Thermostat can be used for
cooling as well.
The respective Home Automation addresses are HC+1 UC13-16 for thermostats 1-4, so e.g. when Base
Console has been set to default Base Address A1, T1 sends messages to B13.