Bluetooth stereo headset / BSH-01
Multiple pairs
The BlueVirtu BSH-01 can pair with 3 other devices- typically another BSH-01 for intercom function; your mobile
phone for handsfree talking; and a BAT-01 for non-Bluetooth audio sources, phones and radio transceivers.
This makes pairing a little more time consuming and complicated than normal, but if you follow the steps in a careful
and logical manner, everything works out fine. If you get it wrong, you just do the pairing process again and it will
discard the previously paired device.
And you only have to do it once- unless you decide to change the phone, BSH-01 or BAT-01 you want to connect
with.
The BSH-01 has 3 memory 'slots' for paired devices- Device 1, Device 2, and Device 3. You can pair any Bluetooth
device to any slot, but it is best to follow the allocation table below so switching between devices and controlling them
via the buttons is simple and logical- in particular, so button C lets you easily jump between the currently selected
device and intercom mode, and back again.
Button
Device
Preferred Bluetooth devices
A
Device 1
BAT-01 for music, GPS navigator, radar detector, radio transceiver, mobile phone
B
Device 2
Bluetooth mobile phone
C
Device 3
BSH-01 for intercom
If you don't have the allocated Bluetooth device, leave the slot vacant, or you can pair with another type of
Bluetooth device in that slot.
Pairing modes
The BlueVirtu supports two different pairing modes.
•
Mode B
is a special mode used when pairing with another BSH-01 (or any other Bluetooth headset) for
intercom mode
. It lets either headset open or close the channel by tapping button C.
Note: Select pairing
mode B on one BSH-01, and pairing mode A on the other. If you select pairing mode B for both they
will not pair up.
•
Mode A
is used for all other Bluetooth devices.
Pairing modes are entered from the power off state by holding button A down for an extended time beyond normal
power up (5s), and are indicated by red/blue flashing
LEDs
and a 4-tone sequence in the headset.
Once in the desired pairing mode, the target device number is selected by pressing button A, B or C for device 1, 2 or
3.
Button A time
LEDs
Tones
State
Comments
Approx 5
seconds
Blue flash
Low-high
Power up
Approx 8
seconds
Slow blue/red
4 tone descending
Pairing mode A
Release to enter mode A, then
select device number with button
A, B or C
Approx 11
seconds
Fast blue/red
4 tone descending
Pairing mode B
Release to enter mode B, then
select device number with button
A, B or C
Lets get pairing
•
Follow these step-by-step instructions to pair up you BlueVirtu system.
•
If you don't have the Bluetooth device, you can skip that sequence of steps and leave that device slot vacant,
or you can pair with another Bluetooth device in that slot.
•
You can always come back later to pair up with new devices or overwrite existing pairings.
•
If you have two BSH-01s it is helpful to label them to avoid confusion, as you may be pairing them up
with different Bluetooth phones and BAT-01s
Pairing with another BSH-01 for intercom function
This uses pairing Mode B (for intercoms) and pairs into Device 3 slot
1.
Ensure both BSH-01s are powered OFF
2.
Take the first BSH-01, hold button A down for about 11 seconds until you hear
4 ascending
tones and the
LEDs flash
fast
red/blue
3.
Release button A- it is now in
pairing mode B
4. Tap
button
C
to select
Device 3
slot. You will hear 3 blips indicating Device 3 selected
5.
Take the second BSH-01, hold button A down for about 8 seconds until you hear 4 descending tones and the
LEDs flash
fast
red/blue
6.
Release button A- it is now in
pairing mode A
