EN
EN
>
33
32
<
Handling with multifunction
display
1. Appearance of display
2. Mounting of display
Loosen the clamp retaining bolts of the display and turn the display so that it
is clearly visible and the throttle lever is easy to operate. Subsequently tighten
the fastening screws. Remove the protective film from the display.
3. Control of display
A:
press and hold the ON/OFF button to activate the display.
B:
press the MODE button for a short time to select another function, displaying
TIME, TRIP, ODO, DST, CHA, VOL
etc.
TIME:
time from switching on of display
TRIP:
total distance traveled from switching on the display (in km); To reset the display
value it is necessary to press the MODE button for
a long time
.
ODO:
total distance traveled (in km)
DST:
This functionality is not set up.
CHA:
number of charge cycles (only counts when the charge is below about 30 %
of battery capacity)
VOL:
current battery voltage
C:
press the ON/OFF button for a short time, the speed mode number will flash
on the display, then press the MODE button, the speed changes (L1 is low, L2
is medium, L3 is fast), the gears have a memory function, the last used gear
automatically saved. If the battery is fully charged and the charge is less than
70 kg, the appropriate speed is specified below:
L1:
max. speed is about 15 km/hr
L2:
max. speed is about 25 km/hr
L3:
max. speed is about 35 km/hr
Cruise control
Cruise control is activated when the power/speed is maintained for about 6–10
seconds: the symbol
appears on the display. Cruise control maintains engine
power (speed may vary depending on terrain, for example) without holding the throttle.
The cruise control feature is canceled by pressing the brake or throttle lever.
The symbol disappears from the display. The cruise control function can be
removed in the settings of function P6.
USB port
There is a USB port on the back of the display to power/charge your mobile phone
or tablet while the e-scooter is running. When the phone is connected, “CH” appears
in the display and the charging time is counting down.
Note:
The USB port is not
compatible with all iPhone devices.
Error messages
If the e-scooter has an error, the display may show an error symbol:
brake error (this symbol is always displayed when the brake lever is depressed
– this is not considered a malfunction)
engine
defect throttle
defect control
unit
defect
4. Display settings
The e-scooter is already set for use. We recommend NOT TO CHANGE PO, P1,
P2, P3, and P4 modes. Press the MODE and ON/OFF buttons simultaneously to
enter the setup mode. PO is displayed, then press the MODE button, displaying P1.
Press the MODE button to continue, displaying P2, P3 P4, P5, P6.
P0
= setting the wheel diameter of the e-scooter
P1
= undervoltage setting
P2
= speed display setting
P3
= speed measurement method (higher value = higher speed)
P4
= setting of miles and kilometers (0 = km, 1 = miles)
P5
= accelerator (0 reacts at zero speed/1 – necessary to push off,
reacts after pushing off)
P6
= cruise control activation
P7
= acceleration after start (1 = strong acceleration)
P8
= maximum speed limit
P9
= efficiency of electric brakes (0 = none, 1 = weak, 2 = efficient)
Function
Set value
from
production
Setting options
P0
08
Wheel diameter in inches. Not necessary to set.
P1
315
Undervoltage protection. DO NOT CHANGE, the battery may be
damaged or deteriorated.
P2
15
Adjustment of speed display. Higher value = lower speed
P3
0
Speed measurement method. DO NOT CHANGE.
P4
0
Speed unit. 0 = km/hr., 1 = mile/hr.
P5
1
Throttle lever functionality. 1 = gas reacts only after pushing off with foot.
P6
1
Cruise control. 0 = cruise control will not work.
P7
0
Acceleration after start. 1 = fast (not smooth)
P8
100
Maximum speed limit Lower value = lower max. speed
P9
2
Efficiency of electronic brake. 0 = none, 1 = weak, 2 = efficient
