Bluerock Tools 8

  8 ” Z 1   C O R E   D R I L L  

Safety 

DO NOT USE THIS MACHINE UNLESS YOU HAVE READ THE 

OPERATING INSTRUCTIONS! 

Safety glasses must be worn at all 
times in work areas. 

Long and loose hair must be 
contained.   

 Appropriate footwear must be worn. 

Close fitting/protective clothing 
must be worn. 

Safety gloves should be worn at all 

times and jewelry must not be worn. 

Hearing protection should be 
worn when using this machine. 

Hard-hat must be worn while using 
machine. 

Dust mask must be worn while 
using this machine. 

 Read operational manual prior to use.  

 

 

PRE-OPERATIONAL SAFETY CHECKS 

Ø

 

Examine the power cord and plug for damage.  This tool is supplied with a ground plug and 
must always be used with the proper grounded circuit.    

Ø

 

Examine the body of the machine and inspect for damage or defects.   

 
 

OPERATIONAL SAFETY CHECKS 

Ø

 

ONLY to be operated by qualified personal who have read instructions. 

o

 

NOTE: Failure to read and follow instructions could result in electrical shock, fire, 
property damage and/or serious injury! 

Ø

 

DO ensure all non-essential people are clear of the immediate work area.  

Ø

 

DO be attentive at all times.  Keep your eye on the work piece.  Always be in a sensible state 
of mind and do not use the machine if you cannot fully concentrate.   

Chapter 

 

Содержание 8"Z1

























Отзывы: