background image

Instructions for Connecting Piping to

Indoor Unit

1.  Align the center of the two pipes that you will 

connect. See 

Fig. 6.7.

2.  Tighten the flare nut as tightly as possible by 

hand.

3.  Using a spanner, grip the nut on the unit 

tubing.

4.  While firmly gripping the nut on the unit 

tubing, use a torque wrench to tighten the 

flare nut according to the torque values in the 

Torque Requirements table below. Loosen 

the flaring nut slightly, then tighten again.

Note: Use of an approved refrigerant sealant is 

recommended for all flare joint connections.

Refrigerant Piping 

Connection

Page 16 

Revised 5/14/2020

6.  Place flaring tool onto the form.
7.  Turn the handle of the flaring tool clockwise until 

the pipe is fully flared.

8.  Remove the flaring tool and flare form, then 

inspect the end of the pipe for cracks and even 

flaring.

Step 4: Connect pipes
When connecting refrigerant pipes, be careful not 

to use excessive torque or to deform the piping in 

any way. You should first connect the low-pressure 

pipe, then the high-pressure pipe.

MINIMUM BEND RADIUS

When bending connective refrigerant piping, 

the minimum bending radius is 4in. See 

Fig.6.6.

≥4in

Radius

Fig 6.6

Fig 6.8

Indoor unit tubing

Flare nut

Pipe

Fig 6.7

Torque Requirements

Outer Diameter of Pipe (inch)

Tightening Torque (ft/lb)

Add. Tightening Torque (ft/lb)

1/4"

11 ft/ lb

12 ft/ lb

3/8"

18 ft/ lb

20 ft/ lb

1/2"

25 ft/ lb

26 ft/ lb

5/8"

33 ft/ lb

35 ft/ lb

Excessive force can break the nut or damage the refrigerant piping. You must not exceed torque 

requirements shown in the table above.

DO NOT USE EXCESSIVE TORQUE

Содержание BM12M22CNS





















Отзывы: