manualshive.com logo in svg

BlueLine VORTEX 7000HHP, Руководство пользователя

Поделиться
Скачать
BlueLine VORTEX 7000HHP Скачать руководство пользователя страница 36

SECTION 3 

32  

BLUE

LINE VORTEX 7000HHP 

25 hours.

 If the hoses show any signs of damage 

or impending rupture, replace the hoses. 
 

!

 

NEVER attempt to repair high-pressure 
solution hoses. Repairing high-pressure solution 
hoses may result in severe burns and serious 
injury, damage to property or fatality. 
 
All high-pressure solution hoses must be rated 
for 3000 PSI at 300 deg. F. Thermoplastic hoses 
do not meet this requirement and should not be 
used. Severe burns and serious injury, damage 
to property or fatality may result if the hoses do 
not meet these requirements. 

 

7. GENERAL SERVICE 
ADJUSTMENTS 

!

 

DO NOT attempt to service this unit while it is 
running. High speed parts as well as high 
temperature components may result in severe 
injury, severed limbs, or fatality. 
 

 

VACUUM RELIEF VALVE 

With the unit running at full RPM, block off the 
airflow at the vacuum inlet ports and read the 
vacuum gauge. If adjustment is required, disengage 
the PTO (power take off) unit, and adjust the 
tension with the locking nut on the vacuum relief 
valve. Reengage the PTO unit and read the vacuum 
gauge. Repeat this process until the vacuum relief 
valve opens at 15” to 17” Hg. 

 

 

 

VACUUM PUMP DRIVE BELTS 

The 

VORTEX 7000HHP

®

 

mobile truck unit is 

equipped with an adjustable belt tensioning 
system. Check belts for proper tension 
(approximately 1/2” deflection) and wear. 
Adjust or replace as needed. 
 
Proper alignment of vacuum pump pulley, belt 
tensioner pulley and PTO drive pulley should be 
checked and adjusted in the first 25 hours of 
operation, and whenever belts are removed or 
replaced. 
 
Place a straight edge between vacuum pump pulley 
and belt tensioner pulley, and ensure full contact of 
straight edge on both the right and left side of each 
pulley. Repeat procedure on the PTO and belt 
tensioner pulley. Adjust vacuum pump and or PTO 
drive as needed and ensure all bolts are properly 
tightened. 

 

 

WATER PUMP DRIVE BELT 

To tighten the water pump belt: 
 
1. Loosen the bolts, which hold the water pump 
and oil pump to the frame base. 
 
2. Adjust the position of the belt tensioning 
adjusting bolt until the proper belt tension is 

Содержание VORTEX 7000HHP























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды