manualshive.com logo in svg

BlueLine VORTEX 7000HHP, Руководство пользователя

Поделиться
Скачать
BlueLine VORTEX 7000HHP Скачать руководство пользователя страница 32

SECTION 3 

28  

BLUE

LINE VORTEX 7000HHP 

 

6. MAINTENANCE 

This section of the operator’s manual contains the 
service and maintenance information for the 

VORTEX 7000HHP

®

 

mobile cleaning unit. A 

planned preventative maintenance program will 
ensure that your 

BLUE

LINE 

VORTEX 

7000HHP

®

 

has optimum performance, long 

operating life, and a minimum amount of down 
time. 

 

!

 

DO NOT attempt to service this unit while it is 
running. High speed parts as well as high 
temperature components may result in severe 
injury, severed limbs, or fatality. 
 
Note: When operating your mobile power unit, 
the engine will operate at 1400 to 1700 rpm’s. 
This is equivalent to 50 miles of highway use per 
hour. The hour meter on your unit’s control 
panel should be factored in when scheduling 
regular maintenance intervals. 
 

 

ENGINE 

Refer to the owner’s manual for specific 
instructions. 
 

1. Check the engine and transmission oil levels 
daily. Ensure that the proper oil level is 
maintained. 

NEVER 

overfill. Check transmission 

and PTO (power take off) hoses and lines for leaks. 
During the first 50 hours of operation, check the 
mounting hardware on the PTO and the PTO drive 
line to ensure it is securely tightened (see 

drive 

belts and pulleys

 for hub torque specifications). 

After 50 hours of use, periodic inspection of the 
PTO oil lines and mounting hardware should be 
performed. Maintenance of the PTO should be 
performed at the same intervals as the 
transmission. Refer to vehicle owner’s manual for 
recommended oil types and regular maintenance 
schedule. 
 

2. Check the engine antifreeze coolant daily. 
Inspect hoses and pipes daily for leaks. Refer to 
owner’s manual if coolant levels are low for 
recommended fluids and fluid levels. 
 

NOTE: 

Additional engine service information can 

be obtained from the vehicle owners’ manual. If 
service or repair is required, contact an authorized 
service center. 
 

 

VACUUM PUMP  

NOTE: 

Refer to the provided Vacuum Pump 

Operation and Service Manual for specific 
instructions. 
 

Lubrication: BLUE

LINE recommends that you 

use only PNUELUBE synthetic blower lubricant in 
the gear ends of the vacuum pump for all operating 
temperatures. PNUELUBE is formulated 
specifically for positive displacement blower 
service to provide maximum blower protection at 
any temperature. One filling of PNUELUBE will 
last a minimum of twice as long as a premium 
mineral oil. 
 

NOTE: 

PNUELUBE (Part # 13-017) is the only 

oil that BLUELINE puts in the vacuum pump at 
the factory. Adding petroleum oil to synthetic oil is 

NOT 

recommended. 

 
1. Check the oil level 

daily

 to ensure the proper 

level. Too little oil will damage and ruin the 
bearings and gears. Too much oil will result in 
overheating. 

Содержание VORTEX 7000HHP























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды