bluelab conductivity pen Скачать руководство пользователя страница 6

Страница: 6 / 9

6.0 Troubleshooting guide

Trouble

Correction

Conductivity pen

gives low readings

Low readings usually mean the probe is contaminated. Clean the

probe and retest in a known solution. Ensure unscented cleaner is

used eg. Bluelab Conductivity Probe Cleaner, Jif, Liquid Vim, Soft

Scrub, Cif cream or Viss.

Conductivity pen

gives high readings

Calibrate pen in a known standard solution.

Check the table in section 4.0 for what solution to use for your

selected conductivity unit.

Screen does not

turn on

Replace unit.

7.0 Technical specifications

Measurement Range

0.0 - 10.0 EC

0 - 5000 ppm (500ppm / TDS)

0 - 7000 ppm (700 ppm)
0 - 50 ˚C / 32 - 122 ˚F

Resolution

0.1 EC, 10 ppm (700), 10 ppm (500)
1 °C / 1 °F

Accuracy at 25 ˚C / 77 ˚F

± 0.1 EC, ± 50 ppm (500 ppm), ± 70 ppm (700 ppm)
± 1 ˚C / ± 2˚F

Temperature compensation

Automatic

Operating temperature

0 - 50 °C / 32 - 122 °F

Calibration

Factory calibrated / manual calibration optional

Units

EC, 700 ppm, 500 ppm, °C, °F

Power source

1 x AAA alkaline battery

English

Содержание conductivity pen










Результаты поиска

Содержание conductivity pen

Отзывы:

Похожие инструкции для conductivity pen

Бренды по названию

Популярные бренды

bluelab conductivity pen, Инструкция по уходу и эксплуатации

Результаты поиска

Содержание conductivity pen

Отзывы:

Похожие инструкции для conductivity pen

Бренды по названию

Популярные бренды