BlueChip SCALA L3 Скачать руководство пользователя страница 9

Scala L3 

  

 

 

Precautions 

Page | 9  

 

General Precautions 

Your Single Board Computer is susceptible to damage by electrostatic discharges. In order to avoid damage, 
you should work at an anti-static bench and observe normal anti-static precautions. Wear an anti-static wrist 
strap connected to an earth point 

before

 opening any packaging.

 

Where a wrist strap is not available, discharge any static charge you may have built-up by touching an earth 
point. Avoid any further movement that could build up another static charge. Touch an earth point from time to 
time to avoid further build-up, and remove the items from their anti-static bags only when required 
 

Electro-Static Discharges 

If you are going to open up the unit, it is important to realise that the devices on the cards within this unit can be 
damaged by static electricity. Bear in mind that the damage caused by static electricity may vary from total 
destruction to partial damage, which may not be immediately obvious. This could have an effect on the 
product's reliability and warranty. Before opening the chassis, ensure that you take necessary static precautions. 
Ideally you should work at an anti-static bench and wear an approved wrist strap or if that is not possible, touch 
a suitable ground to discharge any static build up before touching the electronics. This should be repeated if the 
handling continues for any length of time. 

 

If it is necessary to remove a board or electronic assembly, place it into an anti-static bag. This will prevent any 
static electricity build up damaging the board. Metallised bags are preferred. Do not use black anti-static bags 
for any item containing a battery because these tend to be conductive and will discharge the battery. 

 

On-Board Battery 

The processor board is fitted with a Lithium battery. Great care should be taken with this type of battery. If the 
battery is mistreated in any way there is a very real possibility of fire, explosion, and personal harm. Under NO 
circumstances should it be short-circuited, exposed to temperatures in excess of 100 °C or burnt, immersed in 
water, recharged or disassembled.

 

Expired batteries remain hazardous and must be disposed of in a safe manner, according to local regulations. 

 

Le panneau de processeur est équipé d’une batterie de lithium. Le grand soin devrait être pris avec ce type de 
batterie. Si la batterie est mistreated il y a de dans de toute façon un possibility très vrai du feu, d’expolosion et 
de mal personnel. Dans au cunes circonstances il est sous peu circuité, exposé aux températures au dessus de 
100 degrés de centrigrade ou brûlé, immergé dans l’eau, rechargée ou dissassambled. 
Les batteries expirées restent dazaedous et doivent être reejetées d’une façon sûre, selon des règlements locaux. 

Содержание SCALA L3


































Отзывы: