BLUE SKY AUDIO MANAGEMENT CONTROLLER Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 42

BLUE SKY AUDIO MANAGEMENT CONTROLLER Скачать руководство пользователя страница 16

6. Hit the UPDATE FIRMWARE BUTTON

7. The updater will update the firmware and read the new firmware version.

8. Close the program, disconnect the USB cable and you are done

UPGRADING THE FIRMWARE IN THE AMC REMOTE

Note:

The firmware can only be updated when the remote is disconnected from the rack or the

rack is powered- down..

1. Install the Blue Sky AMC Remote Firmware X.XX update tool. The

installation tool will create a Blue Sky in the Program Files (0x86) sub-directory and

install the update program and the new hex file in that directory.

2. If you get a message that the program requires Elevation and will not run, right click on the

installer and click Run As Administrator.

3. Disconnect AMC Remote and plug-in the USB cable. If this is first time you've
connected the AMC Remote to your computer you may get a message that the
computer is installing drivers for the USB interface.

4. Start the program and the dialog box will show

BLUE SKY
AMC Remote BOOTLOADER REV 1.00
and the currently installed firmware.

5. If the dialog windows says

BLUE SKY
AMC Remote REV x.xx
Application unable to communicate with the device
Power off the unit, disconnect the USB cable, and plug the cable back in and restart
the program.

6. Hit the

UPDATE FIRMWARE BUTTON

7. The updater will update the firmware and read the new firmware version.

Close the program, disconnect the USB cable and you are done

Page

16

«
...
14
15
16
17
18
...
»

Содержание AUDIO MANAGEMENT CONTROLLER











































Отзывы:

Нет отзывов