BLUE SKY AUDIO MANAGEMENT CONTROLLER Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 42

BLUE SKY AUDIO MANAGEMENT CONTROLLER Скачать руководство пользователя страница 11

DIM/CANCEL

– reduces the current system gain by the DIM value. The default setting is -10 dB.

The default setting can be changed utilizing the menu or the AMC Control Software. The
DIM/CANCEL switch is also used to exit the menu mode

MUTE MODE

– the Solo/ Mute channel buttons operate in mute mode. Switching between Solo

and Mute modes clears all solo/mute buttons

SOLO MODE

– the Solo/ Mute channel buttons operate in a Solo Mode. Switching between Solo

and Mute modes clears all solo/mute buttons.

SOLO/MUTE

– Solo’s or Mutes that channel. Solo buttons can now be pressed in unison. For

example if you want to solo L, C, R. so can press those buttons all at once.

PRESETS

– loads the preset.

MENU

– allows a limited number of parameters to be changed on a preset. When exiting the

menu mode, the changed parameters are automatically stored in flash memory.

REMOTE MENU LOCKOUT-

Access to the full menu can be restricted by requiring the user to

enter a 4 digital access code. If this feature is activated, whenever the menu button is pressed, the
user will have to use the preset buttons to input the correct 4 digital code to access the full menu.
A limited user menu can be access by hitting the menu button again. This feature can be turned on
or off and the access code changed using the AMC control software remote code.

REAR PANEL

USB 2.0 CONNECTOR

- used for firmware updates to the remote

REMOTE MAIN RS232

- Connects the Remote to the AMC rack

Page

11

«
...
9
10
11
12
13
...
»

Содержание AUDIO MANAGEMENT CONTROLLER











































Отзывы:

Нет отзывов