background image

Specifications 

Gas Supply Requirements 

 - Australia 

 

 - New Zealand Only: 

 - United Kingdom & EU (CE) 

 

Category:  

II

2H3P 

(20, 37), .

II

2H3B/P 

(20, 28-30),

 

Flue Type:   

A

1.

 

*

 - Measure burner operating pressure at gas control valve outlet test point with burner operating at 

‘High’ setting.  Operating pressure is ex-factory set, through the appliance regulator and not to 
be adjusted, apart from when converting between gases, if required.  (Refer to ‘Gas Conversion’ 
section for details). 

For Refrigeration Cabinet Specifications refer to Refrigeration Cabinet Installation and Operation 
Manual supplied with appliance. 

 

Natural Gas (G20) 

GP513  GP514  GP516  GP518 

GP513 

GP514 

GP516 

GP518 

Heat Input (nett) 

10.5 kW  13.3 kW 

21 kW 

28.5 kW  10.5 kW  13.3 kW 

21 kW 

28.5 kW 

Gas Rate (nett) 

1.11 m

3

/hr 1.41 m

3

/hr 2.22 m

3

/hr 3.02 m

3

/hr 0.81 kg/hr  1.03 kg/hr  1.63 kg/hr  2.21 kg/hr 

Supply Pressure 

20 mbar

 

37 mbar 

Burner Operating Pressure (*) 

8.2 mbar  8.5 mbar 

8.2 mbar 

26 mbar 

Gas Connection 

3

/

4

” BSP Male 

Propane (G31) 

 

Natural Gas 

 

GP513 

GP514 

GP516 

GP518 

GP513 

GP514 

GP516 

GP518 

Input Rating 

(N.H.G.C.)  

40 MJ/hr  53 MJ/hr  80 MJ/hr  108 MJ/hr  40 MJ/hr  53 MJ/hr  80 MJ/hr  108 MJ/hr 

Supply Pressure 

1.13 - 3.40 kPa

 

2.75 - 4.50 kPa

 

Burner Operating Pressure (*) 

0.90 kPa  0.85 kPa 

0.90 kPa 

2.6 kPa 

2.5 kPa 

2.6 kPa 

Gas Connection 

¾” BSP Male 

LP Gas (Propane) 

 

Natural Gas 

 

GP513 

GP514 

GP516 

GP518 

GP513 

GP514 

GP516 

GP518 

Input Rating 

(N.H.G.C.)  

40 MJ/hr  53 MJ/hr  80 MJ/hr  108 MJ/hr  40 MJ/hr  53 MJ/hr  80 MJ/hr  108 MJ/hr 

Supply Pressure 

1.13 - 3.40 kPa

 

2.75 - 4.50 kPa

 

Burner Operating Pressure (*) 

0.90 kPa  0.85 kPa 

0.90 kPa 

2.6 kPa 

2.5 kPa 

2.6 kPa 

Gas Connection 

¾” BSP Male 

LP Gas 

 

LP Gas (G30 - G31) 

GP513 

GP514 

GP516 

GP518 

Heat Input (nett) 

12.0 kW  16.0 kW  24.0 kW  32.5 kW 

Gas Rate (nett) 

0.95 kg/hr  1.26 kg/hr  1.89 kg/hr  2.56 kg/hr 

Supply Pressure 

28 - 30 mbar 

Burner Operating Pressure (*) 

26 mbar 

Gas Connection 

3

/

4

” BSP Male 

Содержание Evolution Series






























Отзывы: