background image

OPERATION - BREWING COFFEE 

A.   PREPARATION 

 
       Place one (1) genuine Bloomfield paper filter in the brew chamber. 
       Add a pre-measured amount of fresh coffee grounds. 
       Gently shake the brew chamber to level the bed of grounds.  
       Slide the brew chamber into place under the brew head. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

B.   AUTOMATIC OPERATION

 

 
       Be sure “READY” light is lit. 

 
       Place the appropriate 

EMPTY

 airpot in place under the brew    

       chamber. 

 
       Press the “BREW” key.  A beep will sound and the BREW            
       INDICATOR LIGHT will glow for the duration of the brew. 
 
      

NOTE:   

VOLUME 1 (top key) is the default brew volume.  

       To brew the OPTIONAL volume: 
       Press and release the VOLUME 2 (bottom) KEY.  The VOLUME 2 
       INDICATOR will glow.  Press the “BREW” key.  A beep will sound 
       and the BREW INDICATOR LIGHT will glow for the duration of the 
       brew. 
       At the conclusion of this brew, the system will revert to the default 
       brew volume, the VOLUME 2 INDICATOR LIGHT will go out, and 
       the VOLUME 1 INDICATOR LIGHT will glow. 
 
       The brew pump will operate for an amount of time  determined by 
       the selected brew volume, drawing a measured quantity of hot    
       water from the tank. 

 
       The hot water will be forced into the brew head where it will spray 
       over the bed of grounds.  Freshly brewed coffee will begin to fill the 
       container under the brew chamber.  When the flow and all dripping 
       stops, the coffee is ready to serve. 
 

D. PREPARE FOR NEXT BREW 

 
       Discard the contents of the brew chamber and rinse it in a sink.  
       When the ”READY ” light glows, the brewer is ready for 
       another brew cycle. 

Fig. 6  Brew Chamber 

CAUTION:   

BURN HAZARD  

 

Exposed surfaces of the 
brewer, brew chamber and  
airpot may be HOT to the 
touch, and can cause    
serious burns. 

 

 

CAUTION:  

BURN HAZARD 

 

To avoid splashing or   
overflowing hot liquids, 
ALWAYS place an EMPTY 
airpot under the brew 
chamber before starting 
the brew cycle.  Failure to 
comply can cause serious 
burns.  
 

 

CAUTION: 

BURN HAZARD 

 

After a brew cycle, brew 
chamber contents are 
HOT.  Remove the brew 
chamber and dispose of 
used grounds with care.  
Failure to comply can 
cause serious burns.  
 

 

NOTE:  

Excessive use of 

the hot water dispense 
function during a brew may 
decrease the amount of 
brew water delivered. 

Содержание Horizon 0420

























Отзывы: