Blonder tongue SDE-6S-ASI Скачать руководство пользователя страница 37

Страница: 37 / 40

SDE-6S-ASI

User Manual

5.14 "Update" Screen

The “Update” screen (Figure 5.14) allows user to browse, select, and download/update the Config file.

Figure 5.14 “Update” Screen

Choose File:

allows the user to select a desired configuration file to be uploaded to the unit from any location on the

computer.

Load & Apply Firmware Update:

Installs the configuration file selected in Choose File #1.

Load Firmware Update From SD Card:

Installs the configuration file when placed loaded on to a SD card (not

supplied) installed in slot located on the encoder's rear panel.

The upgrade process takes about 15 minutes. During this time the user may continuously click on the "Event Log"

tab to view upgrading feedback.

The Event Log will show "System Update Complete" when done. The encoder now requires a reboot, that can be

accomplished by using the power switch or through the hidden Admin page (see Section 5.12 #10 details).

After the reboot, verify the new software/firmware version by going to the Network page (see Section 5.11).

Содержание SDE-6S-ASI









































Результаты поиска

Содержание SDE-6S-ASI

Отзывы:

Похожие инструкции для SDE-6S-ASI

Бренды по названию

Популярные бренды

Blonder tongue SDE-6S-ASI, Руководство пользователя

Результаты поиска

Содержание SDE-6S-ASI

Отзывы:

Похожие инструкции для SDE-6S-ASI

Бренды по названию

Популярные бренды