BLODGETT
www.blodgett.com
44 Lakeside Avenue, Burlington, VT 05401 • Toll Free: (800) 331-5842 • Phone: (802) 860-3700 • Fax: (802) 864-0183
CB42D-10-6K
SHORT FORM SPECIFICATIONS
Provide Blodgett model CB42D-10-6K, one 10 gallon and one 6 gallon direct steam kettle on a cabinet base.
The kettles shall have a double wall interior to form a steam jacket around the lower 2/3 of the kettle. The bottom of the kettle shall be of hemispherical design for superior heat circula-
tion. Steam control valve mounted in leg. The tubular stainless steel mounting legs shall have the steam supply and condensate return pipes completely concealed within the leg meme-
bers. The sealed stainless steel tilt mechanism bearings shall permit the kettle to tilt forward 90° for complete emptying. A removeable operating handle with heat proof knob shall be
mounted on the left or right. Unit shall have a single support leg with nylon insert. Construction shall be all welded satin finish 304 stainless steel with a 316 stainless steel liner.
The cabinet base shall be #4 finish stainless steel with removable side panels, hinged doors with magnetic latches and 6" (152 mm) stainless steel legs with adjustable bullet feet on the
front and flanged adjustable feet on the rear for securing to the floor. Unit shall have steam supply manifold with safety relief valve and condensate return manifold with steam traps for
each kettle. Unit shall have a hot and cold water faucet with control valves, 3" (76 mm) deep sink with drain and two splash guards.
Kettles shall be ASME code stamped and National Board registered. Provide options and accessories as indicated.
SHIPPING INFORMATION:
Approx. Weight:
CB42D-10-6k
370 lbs. (168 kg)
Printed in U.S.A.
NOTE:
FOR COMMERCIAL USE ONLY
NOTE:
The company reserves the right to make substitutions of components without prior notice.
NOTE: SPLASH GUARD NOT SHOWN ON FRONT VIEW
DIMENSIONS ARE IN INCHES [MM]
REAR FLANGED
FOOT DETAIL
7/16" [11mm] HOLES
ON 2.5 [63] B.C.
2 EQUALLY SPACED
Ø
S
D
C H
R
D
Ø
16 [406]
Ø
12
[406]
15
[381]
25.25
[641]
24.75
[629]
20.25
[514]
18
[457]
14.38
[365]
6
[152]
28
[71
1]
58.75
[1492]
S
R
C
H
D
D
36 [914]
11.62 [295]
2.62 [66]
29
[737]
28
[71
1]
26
[660]
18
[457]
14.75
[375]
33
[838]
13.62 [346]
18 [457]
22.38 [658]
D
C
S
H
STEAM SUPPLY: 3/4” IPS for incoming steam at 5-45 PSI
(35-310 kPa). Pressure reducing valve is required if
incoming pressure exceeds 50 PSI (345 kPa).
R
COLD AND HOT WATER: 3/8" O.D. tubing
for cold water to faucet to fill kettle.
DRAIN: 1-1/8” O.D. tubing.
CONDENSATE RETURN: ½” IPS.
APPROVAL/STAMP
P/N S00102 Rev A (1/07)
DIRECT STEAM REQUIREMENTS:
Direct steam at a minimum of 5 psi (34 kPa) and a maximum of 45 psi (310 kPa) 1/4 BHP
required per kettle.
