manualshive.com logo in svg

Blizzard 10x1/1 GN, Инструкция по установке, использованию и обслуживанию

Поделиться
Скачать
Blizzard 10x1/1 GN Скачать руководство пользователя страница 9

5 - 10 - 15 x 1/1 GN ANALOGIC

 

9

 

 

 

 
 

1.3 TRANSPORT OF THE OVEN AND PACKAGING REMOVAL 

 

Upon receipt of the oven and before installing it, check the packaging is intact and there are not visible 
damages. Also check that along with the oven you receive also the documentation, consisting of: 

 

•  Instructions for installation, use and maintenance 
•  Chart to check correct installation 
•  Wiring diagram 
•  Label ISO 3864-1 

 

Before bringing the oven to the point, where it must be installed, check the following: 
•  The doors are large enough to allow passage of the oven 
•  The floor supports the weight. 

 

According to the model of oven, its dimensions and its weight, use suitable facilities to handle goods dur- 
ing transport and installation, able to guarantee stability in order to avoid overturning, falls or uncontrolled 
movements of the appliance or its components. 

 

Keep the oven packed until you reach the site where the oven is going to be installed. 
The packaging makes the handling of goods easier and protects the oven from accidental push. 

 

During moving and installation of the oven, the installer must comply with accident-prevention regulations 
in force at the place of installation (use of safety shoes, gloves, etc.) 

 

Remove the packaging taking care not to damage the oven. 

 

The adhesive film, that protects the surfaces made of stainless steel can be removed also after you have 
positioned the oven on the corresponding stand or the support surface. 

 

ATTENTION

: Packaging materials and adhesive film are potentially dangerous. 

 

For this reason, they must be kept out of the reach of children and properly disposed 
of in compliance with local directives. 

 
 
 
 

You should separate packaging materials (wood, cardboard, plastic...) and dispose of 
them separately, in compliance with directives in force at installation site. 

 
 
 
 

 

Note

: Take the protective film off the stainless steel parts by hand before starting the appliance. 

 

Do not use abrasive substances and/or metal objects. 
Clear any adhesive residues using a sponge soaked in solvent. 

 

If the oven is heated up before removing the adhesive film, the removal of the film and cleaning of residues 
of glue will be much more difficult. 

Содержание 10x1/1 GN

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды