switch
box
v1
intelligent device switch
in μWiFi technology
Do not connect loads with a power greater than the permissible
one.
Connect in accordance with the scheme presented in the manual.
Incorrect connection can be dangerous, it can
result in damage to the controller and loss of warranty.
DANGER! Danger to life due to electric current (also with the de-
vice off), voltage may be present at the outputs. All assembly work
should be carried out ALWAYS with the circuit disconnected
power.
Connecting the device to the power grid without the quality re
-
quirements specified in the standard
PN-EN 50160 results in the loss of warranty.
1
INSTALLATION - BASICS
SAFETY RULES
CONNECTION DIAGRAM
CONTROL DEVICES FROM ANYWHERE IN THE WORLD
Before installing the driver, disconnect the power supply
perimeter. Remember that all assembly work should be carried out at
disconnected supply voltage (disconnecting the mains installation fuse
or unplugging the power cord from the outlet).
The controller should be installed in a place protected against
unfavorable environmental conditions, protected against third parties access – in
a flush-mounted box or inside the controlled housing
devices. Remember that metal parts (wires, housing parts) negatively affect the
range of the device, and thus the comfort of using. It is advisable that the device
be fixed in position
stable and stationary. Necessary due to the operating voltage of the device is that
the connectors in the controller are protected against accidental touch or short
circuit that may result in electric shock or damage to the device.
Familiarize yourself with the diagram and then proceed to the installation of the
controller. Pay particular attention to the labeling of the controller connectors.
Start with connection of the power supply wires - phase L (brown color) and neu-
tral N (blue). Then connect the load. If you decide to local control from a
wall switch, plug in also switch, according to the diagram. For control via
smartphone or tablet only, no wall switch is required.
The controller supports all types of single monostable switches (so-called
bell switches).
After making sure that the device has been connected in accordance with
the diagram and that there are no metal elements near the controller that
could accidentally short-circuit the contacts, turn on the device by swit-
ching on the power supply (switching on the mains installation fuse or con-
necting the power cord to a socket).
FIRST START
2
Unlock your phone or tablet and download the
free wBox application
.
If
you have an Android device, the application can be found in the Play store.
For iOS devices, the application is available in the App Store. The Windows
Phone app can be downloaded from the Windows Phone Store.
Using a mobile phone or tablet, connect to the device’s wireless network.
To do this, enter the settings of your smartphone or tablet, then to the
configuration of the WiFi network and find the network called “switch-
Box-xxxxxxxxxx ” where xxxxxxxxxx is the serial number of the device.
Connect with this one network.
Turn on the wBox application. You will see your device at the top of the
screen. To add it to the application, click “+” on the right side, next to
the name. To preliminarily configure the driver, click on the default device
name.
Test the operation of the controller by clicking the ON / OFF button,
paying attention to connected load behaviour. If you connected a wall
switch, check its operation. In the default configuration for monostable
buttons (so-called bell buttons), holding the button key should turn on the
load, releasing the button will turn the load off. To change this behaviour,
go to settings (button “Settings” in the upper right corner of the screen)
and then in the option “set actions for input”, for the corresponding action
(you can set up a maximum of 10 actions
for the button) select the appropriate action type for the given trigger. For
example, to alternately turn the light on / off with the monostable button
each time it is pressed, select the action type as “change state” and select
“short press” as the trigger.
Also, check the selection in the “state after reboot” which determines the
method behaviour of the controller after a restart caused by e.g. a break in
the supply of electricity. You can choose if the load should stay on, off, stay
in the pre-reboot state (if it was on it should remain turned on, if it was
turned off, it must remain turned off), or take the opposite.
You can also configure it using the phone/tablet web
browser. After connecting with the wireless network of
the controller, turn on the browser and go to the websi-
te: http://192.168.4.1
user manual
device
ACCESS POINT AND WIFI
NETWORK SETTINGS
3
After you run the controller for the first time, you can proceed to its fur-
ther configuration. Being connected to the WiFi network broadcast by
the device, select the device on the control panel of the wBox application,
then go to settings (“Settings” button in the upper right corner screen).
You can change the name of the device under which it is displayed in the
application wBox. In addition, you can change the name and password of
