manualshive.com logo in svg

Blaze King Royal Guardian RGT-3001, Руководство владельца по установке и эксплуатации

Поделиться
Скачать
Blaze King Royal Guardian RGT-3001 Скачать руководство пользователя страница 12

Blaze King

,

 

Royal Guardian,

 

Model RGT-3001

 

OWNER'S INSTALLATION AND OPERATION MANUAL 

Page 12

  

 

Date Printed: Wednesday, November 07, 2012

 

OM-RGT.PUB

 

Version 1.03

 

PREPARATION AND ASSEMBLY

 

 

WARNING

 IMPROPER ASSEMBLY AND/OR INSTALLATION OF YOUR BLAZE KING WOOD STOVE OR FAILURE 

TO OPERATE IT ACCORDING TO THE GUIDELINES DETAILED IN THESE INSTRUCTIONS, WILL VOID THE 
STOVE WARRANTY, CAN CAUSE A HOUSE OR CHIMNEY FIRE, AND MAY ENDANGER YOU FAMILY. FOR 
YOUR SAFETY, FOLLOW THE ASSEMBLY AND INSTALLATION INSTRUCTIONS CAREFULLY.  CONTACT LOCAL 
BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTIONS IN YOUR AREA.  
PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE YOUR NEW STOVE

 

 

This Blaze King Model RGT-3001 Wood stove is Listed by INTERTEK TESTING SERVICES, ONLY if: it is connected 
to a suitable masonry chimney, or a 6 Listed Residential Type and Building Heating Appliance Type Chimney System 
(hereafter referred to as Chimney) and minimum clearances to combustible (burnable) materials are observed. See 
CHIMNEY and CHIMNEY CONNECTOR, and Table 1, Page 19 for minimum clearances.

 

 

DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

 

 

TOOLS NEEDED FOR INSTALLATION

 

If you are planning to install this stove yourself, you will need the tools listed below. Consult the chimney and chimney 
connector manufacturer's installation instructions for tools needed for installation. 
a.  1/4 Wrench, Nut driver, or Socket with Handle 
b.  Medium Flat Blade Screwdriver and Square Screwdriver. 
c. Tape 

measure. 

d. Carpenters 

Level. 

e.  See Mobile Home section for tools needed for Mobile Home stove installations.

 

 

PLANNING FOR YOUR STOVE PLACEMENT

 

As you plan your installation, consider the following:

 

a.  Stove should be placed in the most central location in the home.  Consider safety, convenience, traffic flow, and the 

fact that the stove will need a chimney and chimney connector 

b.  MINIMUM CLEARANCES SHOWN IN FIGURES 21-26, PAGE 20 ARE TO PREVENT WALLS AND CEILINGS 

FROM CATCHING ON FIRE. 

c.  The dimensions and position of the Floor Protector.  See pages 19 & 20 
d.  The type of chimney system to be used.  See page 19. 
Electrical Power. (Optional) The stove can be equipped with a fan assembly and a seven foot electrical cord.  Do not 
route the cord in front of the stove. 

 

REDUCED WALL CLEARANCES

 

The stove and chimney connector may be placed closer to the wall than shown in Figures 21-26, Page 20 if the wall is 
properly protected.  The two wall protection systems described on pg. 11 & 12, allow a reduced clearance from the wall 
to the stove.

 

 

CHECK YOUR CHIMNEY

 

Before connecting any wood-burning unit to an existing chimney, inspect the chimney to be sure that it is in good 
condition.  There must be no cracks or holes.  The cross-sectional area must not be less than that of the flue collar (6" 
diameter  28.27 square inches). A proper chimney is crucial for safe, satisfactory operation of any wood heating 
system. Relining or rebuilding may be necessary to make the chimney safe, efficient, and in conformity with local 
codes. 
Masonry chimneys that have a very large cross-section (100 square inches or more) may experience poor draft and 
may require relining to reduce the cross-section and provide a proper draft. 
This is also an ideal time to clean the existing chimney.  For peak efficiency, a clean chimney flue is essential.  A 
qualified professional chimney sweep can perform both inspection and cleaning.  If you choose to clean your own 
chimney, use the proper tools. Homemade cleaners, such as chains, may damage your chimney. 
Be sure the Ash Clean-Out door for the masonry chimney is closed tightly.  This door may be in the wall in the room 
below the chimney or outside near the ground level of the chimney.  This is frequently overlooked, and can cause 
severe drafting problems in masonry chimney installations. 
The chimney MUST extend above the roof at least three feet & two feet above any area of the roof within ten feet of the 
termination of the chimney. 
If the chimney is a prefabricated metal chimney system be sure chimney pipe is attached, together and, to the wood-
burning unit with a minimum of three (3) screws securing each connection.

 

 

DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

 

Содержание Royal Guardian RGT-3001





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды