Blaze King KING KE1107 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 57

Blaze King KING KE1107 Скачать руководство пользователя страница 31

31

Date Printed: 4/28/11

File: G:/pubdata/Manuals\english manuals\OM-KE/PE.pub

OM KE/PE 1006

Version 1.11 Revised: DApril 2011

Optional Accessories

FAN KIT

ASSEMBLY, KEJ and PEJ (P/N Z1714) either this Fan Kit or the Rear Shield (KE # R/S1107 or PE #

R/SP1006) is

REQUIRED FOR

: MOBILE HOME, ANY INSTALLATION

RESIDENTIAL ALCOVE
RESIDENTIAL CLOSE CLEARANCE

NOTE: Fan Kit should be installed before the stove is placed into position

TOOLS NEEDED FOR INSTALLATION

1. Square (Robertson) screw driver.

INSTALLATION (both models)

Fan kits are shipped fully assembled and electrically wired. Each fan assembly is held to the back of the stove with two
screws.

To begin, remove the two plates behind the vents at the top back of the stove. Replace all screws.
Re-move fan kit from packaging and inspect, paying particular attention to the fans. The fan blades must turn freely.
Each fan/fan tube assembly attaches with the fan at the bottom, and the assembly with the speed control switch on the
same side as the thermostat and bypass controls.

Hook the top of the fan tube over the stovetop and inside the stove top vent. Start the screw that is below the fan, into
the slotted bracket on the bottom back of the stove body. Align the assembly so that the fan tube is parallel with the main
air tube down the center of the stove.

Tighten the screw below the fan to push the fan tube up. Tighten the top screws so the entire assembly is snug against
the stove body.

Manufacturing tolerances allow some space around control shafts and welds. The intent is to minimize the air gaps
around the tube, and to lessen the possibility of rattles.

ELECTRICAL CONNECTION

Your Blaze King fan kit is equipped with a three-prong (grounded) plug to decrease shock hazard. THIS PLUG SHOULD
BE INSERTED DIRECTLY INTO A PROPERLY-GROUNDED, THREE-HOLE RECEPTACLE. DO NOT CUT OR
REMOVE THE GROUNDING PRONG FROM THIS PLUG. Do not route the power cord in front or under the stove.

Note:

"When your Blaze King is equipped with the Dual Fan assembly, remember that air movement across the top of

the stove can cause an inaccurate thermometer reading. Simply turn off your fans at the rheostat for 5 minutes to allow
for a corrected reading."

«
...
29
30
31
32
33
...
»

Содержание KING KE1107


























































Отзывы:

Нет отзывов