manualshive.com logo in svg

Blaze King Clarity CL2118 SP, Руководство по эксплуатации и установке, Страница: 30 / 56

Поделиться
Скачать
Blaze King Clarity CL2118 SP Скачать руководство пользователя страница 30

180-CL2118-SP v1.00

May 22, 2018

Page 30

Clarity CL2118 SP

INSTALLATION

ON VERTICAL PIPE RUNS A MINIMUM VENT CLEARANCE OF 1” (26 mm)

TO COMBUSTIBLES MUST BE MAINTAINED

ON HORIZONTAL PIPE RUNS A MINIMUM VENT CLEARANCE OF 13” (330 mm) ABOVE,

2 1/2” (64 mm) ON SIDES, AND 1” (26 mm) BELOW, MUST BE MAINTAINED

The rigid vent systems use twist lock connections.  The fl ue collar attached to the unit connects to the 
approved venting system.  While you are assembling the pipe, bear in mind the best visual appearance.  
Seams should be aligned and hidden as much as possible.  Make sure you twist the mating section all the way 
to make a solid connection.

As this system is a sealed system, a high temperature sealing compound must be used to seal the 
metal to metal joint:

Apply a bead of high temperature sealant (non-silicone) to both the 4” exhaust and 6-5/8” intake section of the 
male pipe.  The female section of the pipe/fi tting has four indentations evenly spaced around the pipe.  These 
indentations are designed to slide over the male section of the pipe and locate into the four entry slots of the 
male section of pipe.  Twist the female section clockwise a quarter turn to fully lock the sections together.

NOTE:DO NOT USE SILICONE BASED SEALANTS

NOTE: ALLOWING HORIZONTAL VENT PIPE TO SLOPE DOWN TOWARDS THE VENT TERMINATION 

COULD CAUSE POOR COMBUSTION AND/OR HIGH TEMPERATURES THAT MAY PRESENT A FIRE 

HAZARD.

Mark a 10” x 10” square around the center mark (inside dimensions).  Cut and frame the exterior wall to accept 
the wall penetration heat shield.  Install the penetration shield using wood screws.  If the wall being penetrated 
is constructed of non-combustible material a 7” hole is acceptable for the vent pipe.

CAUTION: When installing the termination on to vinyl siding, a vinyl siding kit must be used.

This prevents the termination from being recessed into the siding.

When the termination is to be attached to vinyl siding apply a bead of non-hardening mastic around the 
outside edge to form a seal between the standoff  and the termination cap.  Attach the termination cap to the 
exterior wall inserting four wood screws through the holes in the corner of the vent termination.  Complete the 
installation by applying a bead of mastic around the outer edge of the vinyl standoff .  
With the termination cap installed you can now connect the completed vent assembly by sliding the unit back 
towards the wall and carefully inserting the pipe into the terminal.  Before the fi nal connection is made slide on 
the decorative wall thimble.  Secure the termination cap by securing the termination straps to the pipe as close 
to the exterior wall as possible using sheet metal screws.  Ensure that the straps are hidden by the wall thimble 
cover.  Apply decorative trim if required.

Содержание Clarity CL2118 SP

























































Отзывы:

Нет отзывов