background image

POWER ON LED - 

This light will turn on when the amplifier receives a

+12V turn on signal from the radio.  If the amp is properly wired, but the
light does not turn on, there may be a short circuit condition that the amp
is protecting itself from.  

BASS BOOST -

This control provides additional bass in the 45Hz area to

give a stronger low end “feel” to the bass.  Once switched on, this will
also allow  the amp to be driven into distortion sooner so the user must
be aware.

GAIN CONTROL -

The gain control allows for a range of 0.3-6Volts input.

This means that if the setting is a 0.3V, it only takes 0.3Volts to drive the
amp to full output.  

(Such a low setting allows for the amp to be easily

overdriven and more susceptible to noise so a mid-position is highly
recommended for most radios.)

LOW-PASS FREQUENCY -

If the mode selector is in the “LP” position

the amplifier passes only low frequency sound.  The upper limit for such
sound is set via this control.  For bass, a value just below 100Hz is usually
best.

HIGH-PASS FREQUENCY -

If the mode selector is in the “HP” position

the amplifier passes only mid and high frequency sound.  The lower limit
for such sound is set via this control.  A common setting is just above
100Hz.

CROSSOVER MODE - 

Depending upon the system design chosen, you

need to set the amplifier in the proper “mode” be it LP, Fullrange, or HP.
The low-pass and high-pass frequency settings are explained above.  The
“full-range” setting simply allows for the amp to pass all audio frequencies
without any kind of crossover filter application.  

(This is common with

6x9” fullrange coaxial speakers for example.)

C

ONNECTIONS

& C

ONTROLS

– 

7

L (+)

L (–)

R (+)

R (–)

white

white/black

black

gray

gray/black

NOT

USED

     "HLA1"
High Level Adaptor

(LOOP-THRU)

INPUTS

R

(BR)

L

L (+)

R (+)

white

white/black

black

gray

gray/black

NOT USED

     "HLA1"
High Level Adaptor

(LOOP-THRU)

INPUTS

R

(BR)

L

NOT USED

Radio chassis or

common speaker

ground

"Ganged" 20k/ch

Resistor pack

(L)

(R)

(GND)

POWER ON LED

CROSSOVER MODE:  LP - FULLRANGE - HP

(Crossover is either in Low-pass, Full-range, or High-pass mode)

HIGH-PASS FREQUENCY:  “50 - 250Hz”

(Frequencies above this setting will be passed through)

LOW-PASS FREQUENCY:  “50 -250Hz”

(Frequencies below this setting will be passed through)

GAIN CONTROL : “0.3 - 6.0 Vrms”

(this is the input voltage necessary at this position for full output power)

BASS BOOST:  “ON/OFF”

(+10dB when ON)

REMOTE GAIN CIRCUITRY

Should the installer wish to create their own remote gain control, or
attempt to daisy chain the gains of multiple amps, refer to the adjacent
circuit design for proper connection.  This should ONLY be attempted by a
very highly qualified installation technician.  If improperly done 

DAMAGE

WILL OCCUR

to the amplifier and 

WILL NOT

be covered by warranty!

(We put this information in this manual because of the interest of our
highly skilled Blaupunkt installers - the average consumer should NOT
attempt this on their  own!)

You should 

ONLY

loop the 

SIGNAL

pin to other amps - DO NOT carry the

ground and +12V pin voltages to adjacent amps.

"Floating Ground"

Radio Outputs

"Common Ground"

Radio Outputs

REMOTE GAIN

CIRCUITRY

Содержание PA2150















Отзывы: