Blade CG02+ 3-Axis Скачать руководство пользователя страница 16

16

EN

Compliance Information for the European Union

Instructions for disposal of WEEE by users in the European Union

This product must not be disposed 
of with other waste. Instead, it is the 
user’s responsibility to dispose of their 
waste equipment by handing it over 
to a designated collections point for 
the recycling of waste electrical and 
electronic equipment. The separate 
collection and recycling of your 

waste equipment at the time of disposal will help 
to conserve natural resources and ensure that it is 
recycled in a manner that protects human health and 
the environment. For more information about where 
you can drop off your waste equipment for recycling, 
please contact your local city offi ce, your household 
waste disposal service or where you purchased the 
product.

EU Compliance Statement:

Horizon Hobby, LLC  hereby declares that 
this product is in compliance with the 

essential requirements and other relevant provisions 
of the R&TTE.

A copy of the EU Declaration of Conformity is available 
online at: http://www.horizonhobby.com/content/
support-render-compliance.

IC Information

This device complies with Industry Canada license-
exempt RSS standard(s). Operation is subject to the 
following two conditions:
(1) this device may not cause interference,

and (2) this device must accept any interference, 
including interference that may cause undesired 
operation of the device.

Содержание CG02+ 3-Axis


















Отзывы: