background image

BLADE OS 5.1 Release Notes

6

BMD00098, December 2009

Updating the Switch Software Image

The switch software image is the executable code running on the GbESM. A version of the image 
ships with the switch, and comes pre-installed on the device. As new versions of the image are 
released, you can upgrade the software running on your switch. To get the latest version of software 
available for your GbESM, go to:

http://www.ibm.com/systems/support

From the BLADEOS CLI, use the 

/boot/cur

 command to determine the current software version. 

The typical upgrade process for the software image consists of the following steps:

Place the new image onto a FTP or TFTP server on your network, or on a local computer. 

Transfer the new image to your switch. 

Select the new software image to be loaded into switch memory the next time the switch is reset. 

Loading New Software to Your Switch

The switch can store up to two different software images, called 

image1

 and 

image2

, as well as 

boot software, called 

boot

. When you load new software, you must specify where it should be 

placed: either into 

image1

image2

, or 

boot

For example, if your active image is currently loaded into 

image1

, you would probably load the 

new image software into 

image2

. This lets you test the new software and reload the original active 

image (stored in 

image1

), if needed. 

To download a new software image to your switch, you will need the following:

The image and boot software loaded on a FTP or TFTP server on your network

Boot file: 

GbESM-1-10U-5.1.1.0_Boot.img

Image file:

GbESM-1-10U-5.1.1.0_OS.img

Note – 

Be sure to download both the new boot file and the new image file.

The hostname or IP address of the FTP or TFTP server

The name of the new software image or boot file

Note – 

The DNS parameters must be configured if specifying hostnames.

When the above requirements are met, use one of the following procedures to download the new 
software to your switch. You can use the BLADEOS CLI, the ISCLI, or the BBI to download and 
activate new software. 

Содержание BLADEOS 5.1



























Отзывы: