background image

201-A00     page 2/12

 

SAFETY DATA 

 

Failure to set the vehicle emergency 
brake and chock wheels before 
performing service can cause severe 
personal injury or property damage. 

 

 

Disconnecting fluid or pressure 
containment components during pump 
operation can cause serious personal 
injury, death or major property damage 

 

 

Hazardous pressure 

can cause personal 

injury or property 

damage 

 

Hazardous pressure 

can cause personal 

injury or property 

damage 

 

 

 

 

 

 

Failure to relieve system pressure prior 
to performing pump service or 
maintenance can cause personal injury 
or property damage. 

 

 

If pumping hazardous or toxic fluids, 
system must be flushed prior to 
performing service 

 

Hazardous pressure 

can cause personal 

injury or property 

damage 

 

Hazardous or toxic 

fluids can cause 

serious injury. 

 

 

Failure to disconnect and lockout 
electrical power or engine drive before 
attempting maintenance can cause 
severe personal injury or death 

 

 

Operation without guards in place can 
cause serious personal injury, major 
property damage, or death. 

 

 

Hazardous 

machinery can 

cause serious 

personal injury.

 

 

Do not operate 

without guard  

in place

 

 
 

PUMP DATA 

PUMP IDENTIFICATION 

A pump Identification tag, containing the pump serial number, I.D. number, and model designation, is attached to each pump.  It is 
recommended that the data from this tag be recorded and filed for future reference. If replacement parts are needed, or if 
information pertaining to the pump is required, this data must be furnished to a Blackmer representative. 

 

TECHNICAL DATA

 

 

TX (D) Models 

Maximum Operating 
Temperature * 

240 – 300°F (115 – 149°C) 

Maximum Speed 
size 1.5, 2, 2.5 
size 3 
size 4 

 

780 RPM 
640 RPM 
500 RPM 

Maximum Viscosity 

20,000 SSU (4,250 cSt) 

Maximum Differential 
Pressure 

125 psi (8.6 Bar) 

Maximum Working 
Pressure 

175 psi (12.1 Bar) 

* Maximum operating limits are dependent on the materials of 
construction.  See Blackmer Material Specs 201-091. 

INITIAL PUMP START UP INFORMATION 

Model No.: ___________________________________ 

Serial No.: ___________________________________ 

Date of Installation: ___________________________ 

Pressure Gauge Reading: ______________________ 

Vacuum Gauge Reading: _______________________ 

Flow Rate: ___________________________________

 

 

Содержание TX1.5













Отзывы: