background image

BLACKMER LIQUEFIED GAS PUMPS 

960437

 

INSTRUCTIONS NO. 501-K00 

INSTALLATION OPERATION AND MAINTENANCE INSTRUCTIONS 

MODELS: LGL156C, LGL158C

Section 

Effective 

Replaces 

501 
J

a

n 201

9

 

Jun 2016

 

and Discontinued LGL154C 

TABLE OF CONTENTS 

Page 

SAFETY DATA

1

PUMP DATA

2

 Technical 

Data 

Initial Start Up Information 

INSTALLATION AND OPERATION

 Pre-Installation 

Cleaning 

Location and Piping 

 Pump 

Mounting 

 Coupling 

Alignment 

Internal Pump Relief Valve and Bypass Valve 

 Pump 

Rotation 

To Reverse Pump Rotation 

Underground Tank Applications 

Pre-Start Up Check List 

Start Up Procedures 

MAINTENANCE

 Torque 

Table 

 Strainers 

 Lubrication 

 Vane 

Replacement 

 Pump 

Disassembly 

 Parts 

Replacement 

 Pump 

Assembly 

TROUBLESHOOTING

11

NOTE

: Numbers in parentheses following individual parts indicate 

reference numbers on Blackmer Parts List 501-K01. 

Blackmer pump manuals and parts lists may be obtained from 
Blackmer's website (www.blackmer.com) or by contacting 
Blackmer Customer Service. 

SAFETY DATA 

This is a SAFETY ALERT SYMBOL. 

When you see this symbol on the product, or in the 

manual, look for one of the following signal words and be 

alert to the potential for personal injury, death or major 

property damage 

Warns of hazards that WILL cause serious personal 

injury, death or major property damage. 

Warns of hazards that CAN cause serious personal 

injury, death or major property damage. 

Warns of hazards that CAN cause personal injury 

or property damage. 

NOTICE: 

Indicates special instructions which are very 

important and must be followed. 

NOTICE: 

Blackmer liquefied gas pumps MUST only be installed in 
systems which have been designed by qualified 
engineering personnel. The system MUST conform to all 
applicable local and national regulations and safety 
standards. 

This manual is intended to assist in the installation and 
operation of the Blackmer liquefied gas pumps, and MUST 
be kept with the pump. 

Blackmer liquefied gas pump service shall be performed 
by qualified technicians ONLY. Service shall conform to all 
applicable local and national regulations and safety 
standards. 

Thoroughly review this manual, all Instructions and hazard 
warnings, BEFORE performing any work on the Blackmer 
liquefied gas pumps. 

Maintain ALL system and Blackmer liquefied gas pump 
operation and hazard warning decals. 

Содержание LGL154C













Отзывы: