BLACKMER HXL10E страница 8 Скачать руководство пользователя

Страница: 8 / 16

102-A00 page 8/16

MAINTENANCE

VANE REPLACEMENT

NOTICE:

Maintenance shall be performed by qualified technicians
only, following the appropriate procedures and warnings
as presented in manual.

Figure 5 – Vane Installation

1. Vanes may be replaced with the pump in the upright

position.

2. Flush the pump per instructions in this manual. Drain

and relieve pressure from the pump and system as
required.

3. Remove the head assembly from the

outboard

(nondriven) side of the pump according to steps 4 - 8 in
the "Pump Disassembly" section of this manual.

4. Turn the shaft by hand until a vane comes to the top

(12 o'clock) position of the rotor. Remove the vane.

5. Install a new vane, ensuring that the rounded edge is

UP, and the relief grooves are facing towards the
direction of rotation. See Figure 5.

6. Repeat steps 3 and 4 until all vanes have been replaced.

This method of vane installation ensures the push rods
do not fall out of their rotor slots.

7. Reassemble the pump according to the "Pump

Assembly." section of this manual.

Содержание HXL10E

















Результаты поиска

Содержание HXL10E

Отзывы:

Похожие инструкции для HXL10E

Бренды по названию

Популярные бренды

BLACKMER HXL10E, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HXL10E

Отзывы:

Похожие инструкции для HXL10E

Бренды по названию

Популярные бренды