SECTION 15: S
ERVICING
I
NSTRUCTIONS
61 of 73
Vent Pipe
Venting must be intact. Using a flashlight, look for obstructions, cracks on the pipe,
gaps in the sealed areas or corrosion.
The area must be free of dirt and dust.
Remo
v
e any carbon deposits or scale using a
w
ire brush.
See Page 49, Section 11
.
Outside Air Inlet
Inlet must be intact. Look for obstructions, cracks on the pipe, gaps in the sealed
areas or corrosion.
The area must be free of dirt and dust. Clean and reinstall as required.
Tubes
Make sure there are no cracks.
Make sure tubes are connected and suspended securely.
See Page 11, Section 5
.
Make sure there is no sagging, bending or distortion.
Gas Line
Check for gas leaks.
See Page 52, Section 12
.
Burner Observation
Window
Make sure it is clean and free of cracks or holes.
Clean and replace as required.
Blower Scroll, Wheel and
Motor
Compressed air or a
v
acuum cleaner may be used to clean dust and dirt.
Burner Cup and Orifice
Clear of obstructions (e
v
en spider
w
ebs
w
ill cause problems).
Carefully remo
v
e any dust and debris from the burner.
Electrode
Replace if there are cracked ceramics, excessi
v
e carbon residue, or erosion of the
electrode.
The electrode gap should be 3 mm.
Thermostat
There should be no exposed
w
ire or damage to the thermostat.
See Page 54, Section 13
.
Suspension Points
Make sure the heater is hanging securely.
Look for signs of
w
ear on the chain or ceiling.
See Page 11, Section 5
.
Sports Hall Guard,
Decorative and Protective
Grilles (optional)
The grille must be securely attached. If the grille is loose or off, contact a contractor
qualified in the installation and ser
v
ice of gas-fired heating equipment for repair.
Check that side reflector extensions are installed correctly and secured in place if
necessary. (Decorati
v
e grille only.)
See Page 44, Section 10.3.3
and Page 45, Section 10.4
.
Make sure shield is installed correctly and secured in place if necessary.
(Decorati
v
e grille only.)
See Page 44, Section 10.3.2
.
Wall Ta
g
If a
w
all tag is present, make sure it is legible and accurate. Please contact
Roberts-Gordon Europe Limited or your ROBERTS GORDON
®
independent
distributor if you need a
w
all tag.
See Page 4, Section 2.1
.
Safety Labels
Product safety signs or labels should be replaced by the product user
w
hen they are
no longer legible. Please contact Roberts-Gordon Europe Limited or your
ROBERTS GORDON
®
independent distributor to obtain replacement signs or
labels.
See Page 3, Figure 1
through Page 3, Figure 2
.
Содержание HE15ST
